LEGRAND DA-LITE Tensioned Advantage Series User Manual Download Page 52 | Manualshive

Page: 52 / 61

background image

52

DISCLAIMER

IMPORTANT SAFETY INSTRUCTIONS

ORIGINAL INSTRUCTIONS

5. The use of an accessory attachment not

recommended
by the manufacturer may cause a risk of fire,
electric shock, or injury to persons.

6. Failure to provide adequate structural strength

for this component can result in serious personal
injury or damage to equipment! It is the
installer’s responsibility to make sure the
structure to which this component is attached
can support the weight of all equipment.
Reinforce the structure as required before
installing the component.

7. Use this projection screen only for its intended

use as described in these instructions. Do not
use attachments not recommended by the
manufacturer.

Save These Instructions

Legrand AV Inc. and its affiliated companies and subsidiaries (collectively, “Legrand AV”), intend to make this
manual accurate and complete. However, Legrand AV makes no claim that the information contained herein
covers all details, conditions or variations, nor does it provide for every possible contingency in connection with
the installation or use of the products described herein. The content herein is subject to change without notice
or obligation of any kind. To the maximum extent permitted by applicable law, Legrand AV makes no
representation or warranty, expressed or implied, regarding the information contained herein. Furthermore,
Legrand AV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in
this document.

Da-Lite® is a registered trademark of Legrand AV. All rights reserved.

When using your video equipment, basic safety
precautions should always be followed, including the
following:

1. Read and understand all instructions before

using.

2. Position the cord so that it will not be tripped

over, pulled,
or contact hot surfaces.

3. If an extension cord is necessary, a cord with a

current rating at least equal to that of the
appliance should be used. Cords rated for less
amperage than the appliance may overheat.

4. To reduce the risk of electric shock, do not

disassemble this appliance. Contact an
authorized service dealer when repair work is
required. Incorrect reassembly can cause electric
shock when the appliance is used subsequently.

«
...
50
51
52
53
54
...
»

Summary of Contents for DA-LITE Tensioned Advantage Series






























































Reviews:

No comments

Related manuals for DA-LITE Tensioned Advantage Series

Brand: Da-Lite Pages: 8

Brand: Panasonic Pages: 17

Multimedia Projector MP8670

Brand: 3M Pages: 2

Brand: Dukane Pages: 2

DIGITAL DLP EP7155

Brand: Optoma Pages: 2

Brand: Barco Pages: 153

Brand: Sim2 Pages: 44

Brand: AccuDual Pages: 6

Brand: Ricoh Pages: 24

Brand: Barco Pages: 233

Brand: Barco Pages: 164

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 13

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands