Operating Instructions
For Standard Control Panel
Right Side Sitting Featured; Left Side Sitting Opposite This View
Operating Instructions
For Standard Control Panel
13
12
To Program and Use the Memory I or Memory II:
1. Adjust the furniture to the best and most comfortable position for you using the toggle buttons.
2. Press and hold the Memory I or Memory II button for three (or more) seconds.
3. Listen for the “beep” to indicate the setting was saved in memory.
• Memory I setting plays a single beep to indicate a successful save.
• Memory II setting plays a double beep to indicate a successful save.
• Three quick beeps play when the setting did not successfully save.
4. The next time you use your furniture, press and release either the Memory I or Memory II button
(not holding longer than two seconds) and the furniture automatically moves to the saved setting.
If no setting is stored, the furniture moves to its home, upright, closed and stored position instead.
Pressing a toggle or button on the control panel will stop the automatic motion of the furniture.
The furniture does not restart once the toggle or button is released. Another press of the Memory I
or Memory II button is required to start the furniture in motion again.
NOTE: All features start in motion upon a Memory button press if the feature is programmed to
recline or extend, except for the headrest.* When the headrest is programmed to extend, the headrest
does not start in motion until the back reaches approximately 40% recline, or its programmed recline
setting if set to less than 40% recline. This is done to guard against an undesirable positioning of the
head and neck when moving into the stored recline setting.
* Furniture must be plugged into a power outlet or powered by the
optional
rechargeable lithium-ion
battery pack for the Memory feature to function. This feature is disabled when powered by the 9-volt
battery backup. Additionally, when powered by the
optional
rechargeable lithium-ion battery pack,
only two features operate at the same time.
To Use the Home Button:
The Home button returns the back to its fully upright position and the legrest, headrest and lumbar
to the fully retracted and closed position.
1. Press and release the Home button. The furniture automatically starts in motion, moving the back,
legrest, headrest and lumbar back to the upright and retracted positions under full, normal power.
All motion stops if any toggle or button is pressed while the furniture is moving to home. The motion
does not resume when the toggle or button is released. Another press and release of the Home
button is required to restart the automatic home program.
NOTE: When the furniture is powered by the 9-volt battery back-up, the back and legrest move to
the home position first. Once the back and legrest are fully upright and retracted, then the headrest
and lumbar begin to move to the retracted, home position. When powered by the
optional
rechargeable
lithium-ion battery pack, the headrest and lumbar return to the Home position first, and then the
back and legrest return to Home.
To Use the USB Charging Port:
Plug the USB cable of a small portable electronic device into the USB charging port. Unplug the USB
cable from the charging port when charging is complete.
The USB port is for charging only and does
not save or transfer data.
NOTE: When the furniture is operating on the 9-volt battery back-up in the power supply, the USB
charge port is disabled. When the furniture is powered by the
optional
rechargeable lithium-ion
battery pack, the USB port is enabled, as long as there is adequate charge.
Back toggle
Press the Back toggle rearward and hold to recline
the back. Or press it forward and hold to return
the back to the upright position. Release the button
to stop the back in any reclined position, or when
fully reclined or fully raised.
Headrest toggle
Press the Headrest toggle forward and hold to
rotate the headrest forward. Or press it rearward
and hold to return the headrest. Release the
button to stop the headrest in any position, or
when fully extended or fully retracted.
USB port
Rearward
Forward
Home button
Press and release the
Home button to return
the furniture to the
upright, closed,
stored position.
Legrest toggle
Press the Legrest toggle rearward and hold
to extend the legrest and tilt the chair body
backward. Or press it forward and hold to close
the legrest and return the chair body. Release
the button to stop the legrest in any extended
position, or when fully raised or fully closed.
Lumbar toggle
Press the Lumbar toggle forward and hold to
increase the lumbar intensity. Or press it rearward
and hold to decrease lumbar intensity. Release the
button to stop the lumbar in any position, or when
fully extended or fully retracted.
Memory I button
Memory II button
Press and release a
Memory button to
automatically move
the furniture to the
stored setting.
(pressing and holding
stores the setting)
– To reduce the risk of burns, electric shock,
serious injury or death:
• Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this
unit if the power control is damaged, wet, in contact with or near spilled water or any
liquid. Do not use the unit if the button activation switch has been exposed to water or
any liquid. Do not handle the plug or remote control with wet hands.
DANGER
USB Output Specifications:
5 VDC, 1.0A
