Back Bracket
Body
Bracket
9
8
Assembly Instructions
Power Rocking Recliner Style Featured
Body
Bracket
F
IGURE
1
F
IGURE
2
F
IGURE
3
F
IGURE
4
F
IGURE
5
F
IGURE
6
Electrical
Components Bag
120 Volt Power Cord
3. Install the back.
•
Continue rotating the back at a slight angle, making sure the headrest and lumbar connections fall
between the rear seat and tailgate, and align the brackets on the back with the brackets on the
body (F
IGURE
2)
•
Lower the back onto the body, making sure the back and body brackets are completely engaged.
-
To make sure the back is properly installed with both sets of back and body brackets
engaged, stand behind the chair and twist the back from side to side. If one or both sides
move out of position the brackets are not engaged (F
IGURE
5). Remove the back and repeat
the steps above.
-
If you are unable to install the back properly, contact your La-Z-Boy
®
dealer for assistance.
•
Lock the brackets by using a screwdriver to push down the locking levers (F
IGURE
3).
4. Remove the power supply box from the electrical components bag. Remove the power supply and
120 volt power cord from the box.
5. Locate the motor connector behind the unit. Connect the motor connector to the power supply
connector. Align the connectors, push together until fully seated and close the locking cover to
secure the connection (F
IGURE
6).
6. Connect the 120 volt power cord to the power supply (F
IGURE
6). Do not plug in until instructed in
the operating instructions.
7. Proceed to the
Battery Backup Assembly Instructions
.
8. To remove the back, unplug the 120 volt power cord from the electrical outlet and disconnect the
power supply from the motor connector behind the unit. Reverse the
Assembly Instructions
steps.
When lifting the back up from the body, to lay across the arms,
make sure
to do so slowly and carefully
to prevent damage to the electrical connections.
Assembly Instructions
Back and body brackets on this
side are not engaged. Remove
the back and reinstall.
Adjustable Headrest
Connection (Blue or Purple*)
Make this
connection
Power Supply*
Adjustable Lumbar
Connection (Gray or Pink*)
Motor Connector
Make this
connection
Tailgate
Rear Seat
– To reduce the risk of injury:
• Do not operate the unit until the back is installed and locked.
• The back of the unit must be lifted for assembly. Please seek assistance if you are
unable to lift at least 45 pounds without strain.
WARNING
NOTICE:
-- To reduce the risk of injury:
• Do not plug in until instructed.
1. Once the furniture is unpacked, carefully remove the red electrical components bag from the body
bracket and set aside; depending on the product purchased, inside the bag are the power supply,
power cord, optional remote and three AAA batteries for the optional remote (F
IGURE
1).
2. Make back electrical connections.
•
Lay the back across the arms of the chair. Turn the locking levers, located on the brackets
attached to the back (one on each side), to a 90° angle (F
IGURES
2
AND
3).
•
Locate and identify the two electrical connections between the back and the body. The color of
the connectors varies by date of manufacture.
-
The blue (or purple) connectors on the left side (sitting) are for the adjustable headrest feature.
One connector routes from bottom of the back panel and the other between the rear
seat and tailgate.
-
The gray (or pink) connectors on the right side (sitting) are for the adjustable lumbar feature.
One connector routes from bottom of the back panel and the other between
the rear seat and tailgate.
•
Carefully rotate the back until the headrest and lumbar actuator cables are able to reach the connectors.
•
Connect the adjustable headrest (F
IGURE
4). Align the pins and sockets in the blue (or purple)
connectors, push the connectors together and close the locking cover to secure the connection.
•
Connect the adjustable lumbar (F
IGURE
4). Align the pins and sockets in the gray (or pink) connectors,
push the connectors together and close the locking cover to secure the connection.
*
Power supplies/connections
may vary by date of manufacture.
Back
Bracket
Locking
Lever
at a 90
Degree
Angle
Locked
Position
* Color varies by date of manufacture.
