19
18
Operating Instructions
For Optional Wireless Remote
Operating Instructions
For Optional Wireless Remote
Install Batteries in the Remote:
The remote requires three (3) AAA alkaline batteries (included; packed inside the electrical components bag).
1. Remove the remote and AAA batteries from the electrical components bag. Remove the plastic
wrap from the batteries.
2. Turn the remote over to access the battery compartment.
3. Slide the battery compartment cover off and set aside (F
IGURE
1).
4. Insert three AAA batteries oriented to match the polarity as in indicated by the markings in the
battery compartment (F
IGURES
2 and 3).
5. Slide the battery compartment cover back in place to close the compartment.
F
IGURE
1
F
IGURE
2
F
IGURE
3
To Program and Use Memory I or Memory II:
1. Use the remote to adjust the furniture to the best and most comfortable position for you.
2. Press and hold the Memory I or Memory II button for three (or more) seconds on either the remote or the cradle.
3. Listen for the “beep” and watch for the LED lights to flash on the remote to indicate the setting was
saved in memory.
• Memory I setting plays a single beep and flashes a single light to indicate a successful save.
• Memory II setting plays a double beep and flashes a double light to indicate a successful save.
• Three quick beeps and flashes of light are transmitted from the remote when the setting did
not successfully save.
4. The next time you use your furniture, press and release either the Memory I or Memory II button (not holding
longer than two seconds), on either the remote or cradle. The furniture automatically moves to the saved
setting. If no setting is stored, the furniture moves to its home, upright, closed and stored position instead.
Pressing any button on the remote or cradle, while the furniture is in motion from a Memory button press, stops
the automatic movement of the furniture. The furniture does not restart once the button is released. Another
press of the Memory I or Memory II button is required to start the furniture in motion again.
If the Memory I or Memory II button is pressed on the remote and then the Do Not Disturb button (cradle) is
turned on, all motion stops. The furniture does not automatically resume and continue the move to a Memory I
or Memory II setting when the Do Not Disturb button is turned off. If the Memory I or Memory II button is pressed
on the cradle and then the Do Not Disturb button is pressed on the cradle, the furniture continues to move to the
stored setting. All Remote commands are ignored when Do Not Disturb is on.
NOTE: All features start in motion upon a Memory button press if the feature is programmed to recline or extend,
except for the headrest.* When the headrest is programmed to extend, the headrest does not start in motion until
the back reaches approximately 40% recline, or its programmed recline setting if set to less than 40% recline.
This is done to guard against an undesirable positioning of the head and neck when moving into the stored
recline setting.
* Furniture must be plugged into a power outlet or powered by the optional rechargeable lithium-ion battery
pack for the Memory feature to function. This feature is disabled when powered by the 9-volt battery backup.
Additionally, when powered by the
optional
rechargeable lithium-ion battery pack, only two features operate at
the same time.
To Use the Home Button:
The Home button returns the back is to its fully upright position and the legrest, headrest and lumbar to the fully
retracted and closed position.
1. Press and release the Home button. The furniture automatically starts in motion, moving the back, legrest,
headrest and lumbar back to the upright and retracted positions.
All motion stops if any button is pressed while the furniture is moving to home. The motion does not resume
when the button is released. Another press and release of the Home button is required to restart the home program.
NOTE: When the furniture is powered by the 9-volt battery back-up, the back and legrest move to the home
position first. Once the back and legrest are fully upright and retracted, then the headrest and lumbar return to
the retracted, home position. When powered by the
optional
rechargeable lithium-ion battery pack, the headrest
and lumbar move to the Home position first, and then the back and legrest move to Home.
Remove
Back Cover
Insert (3) AAA Alkaline Batteries
Polarity Markings Inside
the Battery Compartment
