background image

C2000 Debugger     |    41

©

1989-2023

   Lauterbach        

 

                   

                            

<parameters> which are “Deprecated”

In the last years the chips and its debug and trace architecture became much more complex. Especially the 
CoreSight trace components and their interconnection on a common trace bus required a reform of our 
commands. The new commands can deal even with complex structures.

 BASE

 <address>

This command informs the debugger about the start address of 
the register block of the component. And this way it notifies the 
existence of the component. An on-chip debug and trace 
component typically provides a control register block which 
needs to be accessed by the debugger to control this 
component.

Example

: SYStem.CONFIG ETMBASE APB:0x8011c000

Meaning: The control register block of the Embedded Trace 
Macrocell (ETM) starts at address 0x8011c000 and is accessible 
via APB bus.

In an SMP (Symmetric MultiProcessing) debug session you can 
enter for the components BMC, CORE, CTI, ETB, ETF, ETM, ETR a 
list of base addresses to specify one component per core.

Example assuming four cores: “SYStem.CONFIG COREBASE 
0x80001000 0x80003000 0x80005000 0x80007000”.

COREBASE (old syntax: DEBUGBASE): Some cores e.g. Cortex-
A or Cortex-R do not have a fix location for their debug register 
which are used for example to halt and start the core. In this case it 
is essential to specify its location before you can connect by e.g. 

SYStem.Up

PERBASE and RAMBASE are needed for the RAM Trace Port 
(RTP) which is available on some derivatives from Texas 
Instruments. PERBASE specifies the base address of the core 
peripheral registers which accesses shall be traced, RAMBASE 
is the start address of RAM which accesses shall be traced. The 
trace packages include only relative addresses to PERBASE and 
RAMBASE.

For a list of possible components including a short description 
see 

Components and Available Commands

.

Summary of Contents for C2000






























































Reviews: