Lanier AP2145 Setup Manual Download

Page: 366 / 424

Printer Utility for Mac

Restarting the Printer

You can restart the printer.

AAAA

Select

[

Restart Printer

]

on the

[

File

]

menu.

BBBB

Confirm the message that appears on the screen, and then click

[

Restart

]

The printer restarts.

Note

❒

The fonts that you downloaded in the printer's memory will be deleted.

❒

If the printer restarts, all the printer settings return to their defaults.

Downloading PostScript Files

You can download a Postscript file to the printer.

AAAA

Select

[

Download PostScript File...

]

on the

[

Utility

]

menu.

BBBB

Select the file name to download and click the file name, and then click

[

Open

]

CCCC

Type the log file name, and then click

[

Save

]

The selected file is downloaded.

Note

❒

Errors are recorded in the log file.

Summary of Contents for AP2145





































































































































































































































































































































































































































Search results

Summary of Contents for AP2145

Reviews:

Related manuals for AP2145

Brands by name

Popular brands

Lanier AP2145, Setup Manual

Search results

Summary of Contents for AP2145

Reviews:

Related manuals for AP2145

Brands by name

Popular brands