Lanier AP2145 Setup Manual Download | Manualshive

Page: 303 / 424

background image

63

6. Appendix

Configuring the Network Interface Board
with a Web Browser

The Network Interface Board functions as a Web server in addition to allowing
a printer to function as a network printer. You can use a Web Browser to view
the printer status and configure the Network Interface Board.

❖

❖

❖

❖

Configuring the machine

This requires the TCP/IP protocol to be installed. After the machine has been
configured to use the TCP/IP protocol, it will be possible to adjust the settings
using a Web Browser.

Reference

For more information about configuring the machine to use the TCP/IP
protocol, see the Setup Guide.

❖

❖

❖

❖

Operating system browser requirements

Limitation

❒

Sometimes after clicking

[

Back

]

, the previous page may not appear. In this

case, click

[

Refresh

]

or

[

Reload

]

.

❒

The text on the screen may disappear or be aligned incorrectly if the font
size settings of the browser are too large. It is recommended that you use
a font size equal to or smaller than “10 point” with Netscape Navigator,
and “Medium” or smaller with Internet Explorer.

❒

This machine information cannot reload automatically. Click

[

Reload

]

or

[

Refresh

]

on the Web browser when you want to reload this machine infor-

mation.

OS

Browser

Windows 95/98/Me

Microsoft Internet Explorer 3.02 or later
Netscape Navigator 4.0 or later

Windows NT 4.0

Windows 2000

Mac OS 8.6

∼

9.1

Solaris 2.5/2.6/2.7/7/8

«
...
301
302
303
304
305
...
»

Summary of Contents for AP2145









































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AP2145

ZINK PANPRINT01

Brand: Pandigital Pages: 2

Brand: Canon Pages: 36

Brand: Canon Pages: 62

WorkCentre 4260S

Brand: Xerox Pages: 8

Brand: Canon Pages: 738

Brand: Samsung Pages: 143

imageRUNNER 6570

Brand: Canon Pages: 274

Brand: Xerox Pages: 14

Brand: Xerox Pages: 2

imageRUNNER ADVANCE DX C478iZ

Brand: Canon Pages: 208

imageRUNNER ADVANCE DX C477iFZ

Brand: Canon Pages: 92

ApeoSport C5540I

Brand: Fuji Xerox Pages: 108

Brand: Ricoh Pages: 781

Brand: Olivetti Pages: 149

Brand: NBS Technologies Pages: 64

VersaUV LEJ-640

Brand: Roland Pages: 321

Brand: SPRT Pages: 12

Brand: Riso Pages: 150

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands