manualshive.com logo in svg

Lanier AP2145, Setup Manual

The Lanier AP2145 is a high-quality all-in-one printer that offers exceptional performance and versatility. Make sure to download the Setup Manual for free from manualshive.com to easily set up and use this impressive device. This manual will guide you through every step of installation and operation.

Share
Download
background image

NetWare Configuration

44

4

NetWare 3.x - Advanced Settings

The actual procedures for configuring the machine vary depending on whether
the Network Interface Board is configured as a print server or as a remote print-
er. This section describes how to configure the machine in the NetWare 3.x en-
vironment.

Preparation

The following procedures use the Property Sheet method in configuring the
Network Interface Board. If you configure the Network Interface Board as a
NetWare print server for the first time, we recommend you use the Wizard
method. 

⇒

 p.41 “Quick Setup Using the NIB Setup Tool Wizard” 

Note

❒

This section assumes NetWare is functional and that the necessary environ-
ment for the NetWare Print Service is available.

Setting Up as a Print Server

AAAA

Log on to the file server as a Supervisor or a Supervisor equivalent.

BBBB

Run the NIB Setup Tool.

Reference

 

⇒

 p.40 “Running the NIB Setup Tool” 

CCCC

Click 

[

Property Sheet

]

 and click 

[

OK

]

.

The 

[

NIB Setup Tool - Network board list

]

 dialog box of the Network Interface

Board appears.

DDDD

Click 

[

IPX protocol

]

.

Install the NIB Setup Tool

Print Server

Remote Printer

Basic Procedure

Configure the Network Interface Board

Configure the NetWare

Start the print server

Summary of Contents for AP2145









































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AP2145

Canon image Prograf iPF785 Series Basic Manual preview
image Prograf iPF785 Series
Brand: Canon Pages: 136
GBC A1 Operation & Instruction Manual preview
A1
Brand: GBC Pages: 110
Samsung SPP 2020 - Photo Printer - 20 Sheets Manual Del Usuario preview
SPP 2020 - Photo Printer - 20 Sheets
Brand: Samsung Pages: 81
Samsung ML-6000 Bedienungsanleitung preview
ML-6000
Brand: Samsung Pages: 98
Samsung ML-4050N Compatibility Manual preview
ML-4050N
Brand: Samsung Pages: 6
Samsung ML-3750ND User Manual preview
ML-3750ND
Brand: Samsung Pages: 203
Samsung ML-3312ND Manual Del Usuario preview
ML-3312ND
Brand: Samsung Pages: 264
Samsung ML-2165W/XAA Manual Del Usuario preview
ML-2165W/XAA
Brand: Samsung Pages: 228
Samsung ML-2165 User Manual preview
ML-2165
Brand: Samsung Pages: 211
Samsung ML-2525 Brochure & Specs preview
ML-2525
Brand: Samsung Pages: 5
Samsung ML-1865W Manual Del Usuario preview
ML-1865W
Brand: Samsung Pages: 92
Samsung ML-1865W User Manual preview
ML-1865W
Brand: Samsung Pages: 75
Samsung ML-6060 Technical Instructions preview
ML-6060
Brand: Samsung Pages: 11
Samsung ML-1450 Series Manual Del Usuario preview
ML-1450 Series
Brand: Samsung Pages: 206
Samsung ML 3050 - B/W Laser Printer Manual Del Usuario preview
ML 3050 - B/W Laser Printer
Brand: Samsung Pages: 103
Samsung ML 3050 - B/W Laser Printer User Manual preview
ML 3050 - B/W Laser Printer
Brand: Samsung Pages: 215
Samsung ML-1450 Series Quick Manual preview
ML-1450 Series
Brand: Samsung Pages: 2
Samsung CLP 510N - Color Laser Printer User Manual preview
CLP 510N - Color Laser Printer
Brand: Samsung Pages: 266

Brands by name

Popular brands

Load more brands