Lanier AP2145 Setup Manual Download

Page: 184 / 424

Making Printer Settings with the Control Panel

110

Interpreting the Configuration Page

System Reference

❖

Printer ID

Shows the serial number assigned to the board by its manufacturer.

❖

Firmware Version

Shows the version number of the printer firmware.

❖

NCS Version

Shows the version of the Network Interface Board.

❖

IEEE1394

Shows if the optional IEEE1394 board is installed.

❖

Printer Language

Shows the version number of the printer driver language.

❖

Options

Shows the optional trays that you installed.

❖

Pages Printed

Shows the total number of pages printed by the printer to date.

❖

Engine version

Shows the version number of the printer engine.

❖

Total Memory

Shows the total amount of memory (SDRAM) installed on the printer.

❖

Printer Hard Disk

Shows if the optional Printer Hard Disk is installed.

Paper Input

Shows the settings made under the “Paper Input” menu.

Reference

For more information, see p.104 “Paper Input Menu”.

System

Shows the settings made under the “System” menu.

Reference

For more information, see p.116 “System Menu”.

Summary of Contents for AP2145





































































































































































































































































































































































































































Search results

Summary of Contents for AP2145

Reviews:

Related manuals for AP2145

Brands by name

Popular brands

Lanier AP2145, Setup Manual

Search results

Summary of Contents for AP2145

Reviews:

Related manuals for AP2145

Brands by name

Popular brands