Lanier AP2145 Setup Manual Download | Manualshive

Page: 274 / 424

background image

Windows NT 4.0 Configuration

34

3

Changing Port Settings

Follow the steps to change SmartNetMonitor for Client settings, such as Parallel
Printing, Recovery Printing, TCP/IP, the proxy server settings and IPP URL.

Note

❒

There are no settings for the NetBEUI protocol.

AAAA

From the

[

Printers

]

window, click the icon of the printer you want to use. On

the

[

File

]

menu, click

[

Properties

]

.

BBBB

Click the

[

Ports

]

tab, and then click

[

Port Configuration

]

.

The

[

Port Settings

]

dialog box appears

• For TCP/IP protocol, you can configure Recovery Printing, Parallel Print-

ing and Timeout Settings.

• For IPP, you can configure User Settings, Proxy Settings and Timeout Set-

tings.

Note

❒

For more information about these settings, see SmartNetMonitor for Client
Help.

«
...
272
273
274
275
276
...
»

Summary of Contents for AP2145









































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AP2145

Brand: DataCard Pages: 8

WorkCentre 5325

Brand: Xerox Pages: 160

WorkCentre 5016

Brand: Xerox Pages: 2

WorkCentre 490cx

Brand: Xerox Pages: 258

WorkCentre 4260 Series

Brand: Xerox Pages: 210

WorkCentre 3550

Brand: Xerox Pages: 32

WorkCentre 3315DN

Brand: Xerox Pages: 191

WORKCENTER 5222

Brand: Xerox Pages: 28

VersaLink C71 Series

Brand: Xerox Pages: 247

VersaLink C7000

Brand: Xerox Pages: 2

Brand: Xerox Pages: 21

VersaLink B71 Series

Brand: Xerox Pages: 234

WorkCentre 6505

Brand: Xerox Pages: 4

WorkCentre 6015

Brand: Xerox Pages: 16

Brand: Xerox Pages: 4

Brand: Xerox Pages: 5

Brand: Xerox Pages: 8

WORKCENTRE 5735

Brand: Xerox Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands