Lambrecht Ser[LOG] Operator'S Manual Download Page 14

Page: 14 / 129

LAMBRECHT meteo GmbH

Ser[LOG] Manual

Page 14 of 129

Relay out-

puts

The relays "R1" and "R2" are bistable, potential-free changeover switch. At

"C", the signal to be switched is applied. In the idle state there is a switching

connection to "S0", in active state to "S1". The relays may be loaded with up

to 30 V and 0.5 A.

Cover jumper

panel

There is a jumper field under the cover. Via the jumper field of the hardware

drivers COM2 may be switched to COM6 from RS485 to RS422 and 120 Ω

termination resistors are switched in. See Section 13

LED - M -

Measuring

rate

The LED "M" flashes on the set measurement cycle. The light-ON-time is

analogue to the duration of the measurement. After switching on the

Ser[LOG], the LED lights up until the "boot" is complete.

LED – Data

processing

LED "P" flashes during data processing. When 10 minutes average values

are generated, the LED flashes only every 10 minutes. The lighting duration

is analogous to the duration of data processing.

AnDiMod ter-

minal clamp

If the Ser[LOG] is extended with one or more AnDiMod modules, the con-

nection is made via the 4-pin terminal on the bottom of the housing.

Summary of Contents for Ser[LOG]


































































































































Search results

Summary of Contents for Ser[LOG]

Reviews:

Related manuals for Ser[LOG]

Brands by name

Popular brands

Lambrecht Ser[LOG], Operator'S Manual

Search results

Summary of Contents for Ser[LOG]

Reviews:

Related manuals for Ser[LOG]

Brands by name

Popular brands