manualshive.com logo in svg

Lambrecht Ser[LOG], Operator'S Manual, Page: 115 / 129

Share
Download
Lambrecht Ser[LOG] Operator'S Manual Download Page 115

 

LAMBRECHT meteo GmbH 

Ser[LOG] Manual 

Page 115 of 129 

NMEA WG MWD kt   

Wind speed from $WIMWD to kt (kn) (Ser[LOG] converts if deliv-

ered in "m/s") 

NMEA WG MWD m/s  

Wind speed from $WIMWD to m/s (Ser[LOG] converts if delivered in 

"kt") 

NMEA WG kt  MWV   

Wind speed from $WIMWV to kt (kn) (Ser[LOG] converts if deliv-

ered in "m/s") 

15.4.5  Additional serial sensors (proprietary) 

CL31 Cloud Base 1 ft   

Proprietary protocol of the CL31 cloud height measuring device 

from Vaisala. For detailed information on the parameters, please re-

fer to the instructions of the respective sensors. 

CL31 Cloud Base 1 m   
CL31 Cloud Base 2  m  
CL31 Cloud Base 2 ft  
CL31 Cloud Base 3 ft   
CL31 Cloud Base 3 m  
CL31 Cloud Detection Status      
CL31 Highest Signal Detected ft  
CL31 Highest Signal Detected m   
CL31 Vertical Visibility  ft 
CL31 Vertical Visibility  m  
FS11  Backgr. Luminance 10_min   

Proprietary protocol of the Vaisala FS11 visual range finder. For de-

tailed information on the parameters, please refer to the instructions 

of the respective sensors. 

FS11  Backgr. Luminance 1_min    
FS11  FSM102 Window Corr. Factor 
FS11  LM21 Window  Corr. Factor  
FS11  MOR_10_min  
FS11  MOR_1_min   
FS11  Status_BAL  
FS11  Status_IAL  
FS11 Status_VAL  
LD12  Cloud Base 1 ft  

Proprietary protocol of the cloud height measuring device  

LDW HM-12 from Impulsphysik. The sensor is no longer available. 

For detailed information on the parameters, please refer to the 

specifications of the respective sensors. 

LD12  Cloud Base 1 m   
LD12  Cloud Base 2 ft  
LD12  Cloud Base 2 m  
LD12  MROD ft  
LD12  MROD m  
LD12  Vertical Visibility ft   
LD12  Vertical Visibility m  
LD40  Cloud Base 1 ft  

Proprietary protocol of Vaisala's LD-40 cloud height meter. For de-

tailed information on the parameters, please refer to the instructions 

of the respective sensors. 

LD40  Cloud Base 1 m  
LD40  Cloud Base 2 ft   
LD40  Cloud Base 2 m  
LD40  Cloud Base 3 ft   
LD40  Cloud Base 3 m  
LD40  MROD ft  
LD40  MROD m  
LD40  Vertical Visibility ft     
LD40  Vertical Visibility m  
P2_Container_EZ  

Pluvio 2 precipitation sensor in SDI-12 mode. For detailed infor-

mation on the parameters, please refer to the instructions of the re-

spective sensors. 

P2_Container_NEZ   
P2_Int_EZ   
P2_Amount_by_total_NEZ  
P2_Amount_EZ-NEZ   
P2_Amount_NEZ     
P2_Total_amount_NEZ   

Summary of Contents for Ser[LOG]


































































































































Reviews:

No comments