Lambrecht Ser[LOG] Operator'S Manual Download Page 41

Page: 41 / 129

LAMBRECHT meteo GmbH

Ser[LOG] Manual

Page 41 of 129

Note: If the connected sensors are supplied via the "SENSOR SUPPLY" terminals, then all sensors

together must not consume more than 500mA. A higher current consumption puts too much strain on

the Ser[LOG]-Bus and can lead to damage!

5.3

Configuration of the Ser[LOG]

Ser[LOG] and Ser[LOG]Plus are put into operation, configured, and tested with the configuration tool

"Ser[LOG]-Commander".

Ser[LOG]_Commander is a 32 bit Windows application that can be used under the operating systems

Windows XP to Windows 10. The application can be used from a USB memory stick. Installation on the

PC is not necessary.

If you want to copy the Ser[LOG]-Commander to a USB stick or a PC, all files contained in the

PRG_SERLOG folder must be copied as well. The files must always be in the same shared directory.

5.3.1

Basic Station Configuration

Start the Ser[LOG]-Commander by calling the "SerLog_Cmd. exe".

Press the button "Configure Logger" to open the Ser[LOG] configuration window.

The available serial interfaces are deactivated at delivery, therefore the Ser[LOG] can only be reached

via:

•

Mini-USB service interface or

•

USB Bluetooth stick (CSR chipset required)

Both interfaces operate independently of the set baud rate.

5.3.1.1

Configuration via Mini-USB Service Interface

Connect the Ser[LOG] to the PC via the supplied USB-to-Mini USB cable. The Ser[LOG] is not pow-

ered via the USB interface. If it is not already done, connect the Ser[LOG] to a suitable power supply

(10... 30 VDC).

The driver software for the USB service interface is part of the Windows operating system. Under a

freshly installed Windows 10 the interface is recognized as "USB serial device". Windows driver up-

dates can load a "driver" from the company "ELMO" and the interface is then called "ELMO GMAS".

To uniquely identify the USB interface as Lambrecht service port, please update the driver for this in-

terface via the device manager by "updating" the driver. Depending on your operating system please

load the 32- or the 64-bit version from the directory

Ser[LOG]_Cmd\Ser[LOG]_SYNMET_USB_Driver

After this update the interface is recognized as "LAMBRECHT Service Port".

Summary of Contents for Ser[LOG]


































































































































Search results

Summary of Contents for Ser[LOG]

Reviews:

Lambrecht Ser[LOG], Operator'S Manual, Page: 41 / 129

Search results

Summary of Contents for Ser[LOG]

Reviews: