background image

 

LAMBRECHT meteo GmbH 

Ser[LOG] Manual 

Page 53 of 129 

The "Processing" frame defines the routine after which the sensor signal is to be processed. The follow-

ing routines are available: 

Sum 

The Ser[LOG] adds up the measured values and stores the sum for each 

storage interval.  

Average value scalar 

Standard mean value for most measured values. 

Mean value vectorial 

(wind direction) 

Calculation of the vectorial average value for the wind direction. This pro-

cessing opens the "Settings Details" window for the "Vector linked pair of 

wind sensors" (chapter 5.3.6.2) when configuring the sensors. 

Mean value vectorial  

(wind speed) 

Calculation of the vectorial average value for the wind speed. This pro-

cessing opens the "Settings Details" window for the "Vector linked pair of 

wind sensors" (chapter 5.3.6.2) when configuring the sensors. 

Last measured value in storage 

interval 

The last measured value supplied by the sensor at the time of storage is 

stored. If the last value is incorrect, the corresponding error is saved. 

Last valid measured value in 

the storage interval 

The last measured value delivered by the sensor at the time of saving is 

saved. If the value is incorrect, the last valid value is saved. 

Maximum of the storage inter-

val 

The maximum value of the respective storage interval is stored. 

Minimum of the storage interval 

The minimum value of the respective storage interval is stored. 

Total rainfall without correction 

This summation for precipitation quantity sensors with pulse output, (1 pulse 

= x precipitation quantity). With this function, the Ser[LOG] adds up the 

measured values and saves the sum for each storage interval. Please also 

enter the rocker factor (mm per pulse) for this application. 

Total rainfall with correction 

This summation for precipitation quantity sensors with pulse output, (1 pulse 

= x precipitation quantity). With this function, the Ser[LOG] adds up the 

measured values and saves the sum for each storage interval. Please also 

enter the rocker factor (mm per pulse) for this application. In addition, the 

Ser[LOG] calculates a frequency-dependent correction of the precipitation 

quantity. (The correction is only valid for LAMBRECHT precipitation sensors 

without integrated correction.) 

Harmonic mean 

Calculates and stores the harmonic mean value of the measured value. The 

harmonic mean value is automatically set to "0" as soon as a measured value 

in the storage interval has the value "0". 

 

The processing routines "Variance (...)","Standard deviation (...)" are only intended for virtual channels. 

Variance 

Calculates and saves the variance of the measured value. 

Standard deviation 

Calculates and saves  the standard deviation of the measured 

value. 

Standard deviation (wind direction) 

Calculates and saves the standard deviation for the wind direction 

on a vectorial basis of the measured value. 

Standard deviation (wind speed) 

Calculates and saves the standard deviation for the wind speed 

on a vectorial basis of the measured value. 

Variance (wind direction) 

Calculates and saves the variance for the wind direction on a vec-

torial basis of the measured value. 

Variance (wind speed) 

Calculates and saves the variance for wind speed on a vectorial 

basis of the measured value. 

The selection box "Sensor type" categorizes the sensors according to the respective measurement type. 

This information is used by the processing software, e. g. MeteoWare CS-4 on the PC. 
 

 

 

 

 

 

 

Summary of Contents for Ser[LOG]


































































































































Reviews: