L-Acoustics A10i Owner'S Manual Download

Page: 31 / 132

Rigging system description

Additional safety with A10i-LIFT

On each enclosure on which A10i-LIFT is secured, secure a DIN580 eye bolt to the dedicated insert to implement

a secondary safety.
Use a shackle and a steel wire rope. Make sure the steel rope is as tensed as possible without bearing the load.

A scalable radial array of A10i Wide/Focus can be created using multiple A10i-LIFT.

A10i-LIFT quantity and position

Use one A10i-LIFT for up to three enclosures in the array.
Do not leave more than two adjacent enclosures unsupported.
Refer to

APPENDIX A: Authorized congurations with A10i-LIFT

(p.124).

Risk of tilting

When using a single motor or a bridle, make sure the array is symmetrical.

When using a third-party bridle, make sure the angle between the two chains does not exceed 60°.

A10i owner's manual (EN) version 1.0

Summary of Contents for A10i





































































































































Search results

Summary of Contents for A10i

Reviews:

Related manuals for A10i

Brands by name

Popular brands

L-Acoustics A10i, Owner'S Manual

Search results

Summary of Contents for A10i

Reviews:

Related manuals for A10i

Brands by name

Popular brands