L-Acoustics A10i Owner'S Manual Download Page 86

Page: 86 / 132

Rigging procedures

Mounting a KS21i / A10i Wide/Focus assembly with A-U15i and A10i-TILT

Procedure

Fasteners for wall-mounting or ceiling-mounting

Select screw length and anchors applicable to the wall or ceiling properties.

Mount A-U15i on the ceiling or on the wall using four M10 screws.

When using a U-bracket horizontally, make sure the hooks are oriented upwards.

781 mm / 30.7 in

120 mm / 4.7 in

Ø M10 (x4)

Prepare a KS21i by removing the placeholder screws on both sides of the enclosure.

Position A10iKS21i-ULINK on each side of KS21i.

Align A10iKS21i-ULINK with the central inserts of KS21i, and using the screws provided with A-U15i, drive a screw

on each side.
Approximately 5 mm (0.2 in) of the thread must be visible.

5 mm / 0.2 in

Alternatively, drive the screw in the bottom insert for a conguration with the enclosure closer to the ceiling.

A10i owner's manual (EN) version 1.0

Summary of Contents for A10i





































































































































Search results

Summary of Contents for A10i

Reviews:

Related manuals for A10i

Brands by name

Popular brands

L-Acoustics A10i, Owner'S Manual

Search results

Summary of Contents for A10i

Reviews:

Related manuals for A10i

Brands by name

Popular brands