L-Acoustics A10i Owner'S Manual Download Page 73

Page: 73 / 132

Rigging procedures

Adding a pullback with A10i-RIGBAR or A15i-RIGBAR

Type of deployment

own array with pullback

Rigging accessories

A10i-RIGBAR / A15i-RIGBAR
1 x Ø12 mm shackle WLL 1 t (provided)

Additional accessories

M6x40 screws (provided)
M6x18 rigging screws (provided)
T30 Torx bit

Min number of operators

Risk of falling objects

Verify that no unattached items remain on the product or assembly.

Secondary safety

Use available holes on the rigging accessories to implement a secondary safety.

Assembly

Procedure

Prepare a vertical array as described in

Flying a vertical array with A10i-BUMP or A15i-BUMP

(p.59) or

Flying a

vertical array with A10i-RIGBAR or A15i-RIGBAR

(p.71).

Raise the array until the bottom enclosure is accessible.

Remove the screw from the bottom rear hole of the bottom enclosure on each side.

Secure A10i-RIGBAR at the bottom rear of the bottom enclosure.

A10i owner's manual (EN) version 1.0

Summary of Contents for A10i





































































































































Search results

Summary of Contents for A10i

Reviews:

Related manuals for A10i

Brands by name

Popular brands

L-Acoustics A10i, Owner'S Manual

Search results

Summary of Contents for A10i

Reviews:

Related manuals for A10i

Brands by name

Popular brands