manualshive.com logo in svg

Kyocera KM-1650, Service Manual

Share
Download
Kyocera KM-1650 Service Manual Download Page 98

2DA/2DB-1

1-4-29

U110

Checking/clearing the drum count 
Description

Displays the drum counts for checking, clearing the figure. 

Purpose

To check the drum status. Also used to clear the count after replacing the durm during regular maintenance.
Since the count was cleared before shipping, do not clear it when installing. A drum count value less than
150K, however, cannot be cleared.

Method 

1. Press the start key. The drum counter count is displayed.
2. Select the CLEAR using the up/down cursor keys. If the counter value is 150K or less, CLEAR is not dis-

played.

3. Press the start key. The count is cleared, and the screen for selecting a maintenance item No. is dis-

played. 

Completion

To exit the maintenance mode without changing the count, press the stop/clear key. The screen for selecting a
maintenance item No. is displayed.

U130

Initial setting for the developer 
Description

Replenishes toner to the developer unit to a certain level from the toner container that has been installed.

Purpose

To operate when installing the machine. 

Method

1. Press the start key. The screen for executing is displayed.
2. Select the EXECUTE using the up/down cursor keys.
3. Press the start key. Installation of toner starts and time (minutes) is indicated until the installation ends.
4. When the installation is complete, FINISHED will be displayed if the installation is successful or NG will 

be displayed if it has failed. If NG is displayed, check to see if the toner container contains toner and to 
see if the toner container sensor malfunctions and then try again. 

Completion

Press the stop/clear key after operation is complete. The screen for selecting a maintenance item No. is dis-
played.

U144

Setting toner loading operation 
Description

Sets toner loading operation after completion of copying.

Purpose

To set whether or not toner is loaded on the drum after low density copying. Normally no change is necessary
from the initial setting. 

Method

Press the start key. The screen for selecting an item is displayed.

Setting

1. Select either ON or OFF using the up/down cursor keys. The selected item is displayed in reverse.

Initial setting: OFF 

2. Press the start key. The value is set.

Completion

Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Display

Description

ON

Toner loaded

OFF

Toner not loaded

Summary of Contents for KM-1650

























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands