manualshive.com logo in svg

Kyocera KM-1650, Service Manual

Share
Download
Kyocera KM-1650 Service Manual Download Page 114

2DA/2DB

1-4-45

U504

Initializing the scanner NIC
Description

Initializing the optional scanner NIC to its factory default.

Purpose

To return to a setup at the time of factory shipments.

Method

1. Press the start key. The screen for executing is displayed.
2. Select the EXECUTE using the up/down cursor keys. It is displayed in reverse.
3. Press the start key. All data in the scanner NIC is initialized. 

Completion

Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.

U506

Setting the time out
Description

Sets the communication timeout time for connection to a computer.

Purpose

To change the preset value if a communication error occurs after connection to a computer continues for a
long time. By delaying the error detection timing, the error may be cleared. If the error is not cleared after the
preset value is changed, however, return the preset value to the initial value.

Method

Press the start key. The screen for selecting an item is displayed.

Setting

1. Select ON or OFF using the left/right cursor keys. The selected item is displayed in reverse.

The setting can be changed by 10 s per step. 

2. Press the start key. The setting is set, and the screen for selecting a maintenance item No. is displayed.

Completion

To exit this maintenance item without changing the current setting, press the stop/clear key. The screen for
selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Description

Setting range

Initial setting

timeout time

10 to 120 (s)

10

Summary of Contents for KM-1650

























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands