manualshive.com logo in svg

Kyocera KM-1650, Service Manual

Share
Download
Kyocera KM-1650 Service Manual Download Page 238

2DA/2DB-1

2-1-16

(1) Fixing temperature system

Figure 2-1-19 Fixing temperature system

Warm-up control

1. 500 ms after the fixing heater S (FH-S) turns on, the fixing heater M (FH-M) turns on.
2. When the fixing temperature reaches preset temperature, both fixing heater S (FH-S) and fixing heater M (FH-

M) turn off simultaneously.

Ready state control

1. When the fixing temperature drops to the preset temperature, fixing heater S (FH-S) turns on, and after speci-

fied time, the heater turns off.

2. When fixing heater S (FH-S) turns off, fixing heater M (FH-M) turns on at the same time, and after specified 

time, the heater turns off.

3. The operation above is repeated to keep the fixing temperature to the preset temperature.

If a temperature more than or equal to the preset tempe 20

°

C/68

°

F is detected, both fixing heater S 

(FH-S) and fixing heater M (FH-M) are turned off forcibly.

(2) Fixing temperature control based on ambient temperature

This machine performs fixing temperature control based on the ambient temperature.

Fixing heater S (FH-S)

Fixing heater M (FH-M)

HEAT signal

HEAT signal

Time

500 ms

On

On

On

On

On

On

Off

Off

Off

Off

Warm-up
control

Ready state 
control

Temperature 

( C)

Preset temperature ( C)

(secondary stabilization)

Ambient temperature

Fixing temperature (

°

C)

Lower than 13

°

C/55.4

°

F

Reference value +10

Higher than or equal to 13

°

C/55.4

°

F, 

lower than 18

°

C/64.4

°

F

Reference value +5

Higher than or equal to 18

°

C/64.4

°

F, 

lower than 31

°

C/87.8

°

F

Reference value

Higher than 31

°

C/87.8

°

F

Reference value -5

Summary of Contents for KM-1650

























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands