manualshive.com logo in svg

Kyocera KM-1650, Service Manual

Share
Download
Kyocera KM-1650 Service Manual Download Page 122

2DA/2DB

1-4-53

U991

Checking the scanner count
Description

Displays the scanner operation count.

Purpose

To check the status of use of the scanner.

Method

Press the start key. The screen for the scanner operation count is desplayed.

Completion

Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.

U993

Outputting a VTC-PG pattern
Description

Selects and outputs a VTC-PG pattern created in the machine.

Purpose

When performing respective image printing adjustments, used to check the machine status apart from that of
the scanner with a non-scanned output VTC-PG pattern.

Method

1. Press the start key. The screen for selecting an item is displayed.
2. Select the VTC-PG pattern to be output using the up/down cursor keys.

3. Press the interrupt key. The copy mode screen is displayed.
4. Press the start key. A VTC-PG pattern is output.

Completion

Press the stop/clear key at the screen for selecting an item. The screen for selecting a maintenance item No.
is displayed.

Maintenance

item No.

Description

Display

Description

COPY

Scanner operation count for copying

FAX

Scanner operation count for fax

NWS

Network scanner operation count

Display

PG pattern to be output

Purpose

PG1

Center line adjustment

PG2

Lateral squareness adjustment
Magnification adjustment

PG3

-

Summary of Contents for KM-1650

























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands