Kyocera KM-1650 Service Manual Download Page 149

Page: 149 / 280

2DA/2DB

1-5-20

C0510

Third paper feeder*

communication

problem

Communication fails five times succes-
sively.

Paper feeder
installed incor-
rectly.

Check the installation state of the paper
feeder and adjust it if it is not properly
installed.

Defective engine
PCB or drawer
main PCB.

Replace the engine PCB or drawer main
PCB and check for correct operation.

C0610

Bitmap (DIMM) problem

There is a problem with the data or
address bus of the bitmap DRAM.

Defective main
PCB.

Replace the main PCB and check for correct
operation.

DIMM installed
incorrectly.

Check if the DIMM is inserted into the socket
on the main PCB correctly.

Defective DIMM.

Replace the DIMM and check for correct
operation.

C0630

DMA problem

DMA transmission of compressed,
decompressed, rotated, relocated or
blanked-out image data does not com-
plete within the specified period of time.

Defective main
PCB.

Replace the main PCB and check for correct
operation.

C0800

Image processing problem

JAM05 is detected twice.

Defective main
PCB.

Replace the main PCB and check for correct
operation.

C0820

Fax control PCB*

CG ROM checksum

error

A checksum error occurred with the CG
ROM data of the fax control PCB.

Defective fax con-
trol PCB.

Replace the fax control PCB and check for
correct operation.

C0830

Flash ROM program area checksum
error

A checksum error occurred with the pro-
gram of the fax control PCB.

Defective fax con-
trol PCB.

Replace the fax control PCB and check for
correct operation.

C0860

Fax control PCB*

software switch

checksum error

A checksum error occurred with the soft-
ware switch value of the fax control PCB.

Defective fax soft-
ware.

Install the fax software to Ver. 2.xx or later.

Defective fax con-
trol PCB.

Replace the fax control PCB and check for
correct operation.

C0870

Fax control PCB*

to main PCB high-

capacity data transfer problem

High-capacity data transfer between the
fax control PCB and the main PCB of the
machine was not normally performed
even if the data transfer was retried the
specified times.

Poor contact in the
connector termi-
nals.

Check the connection of connector. Repair
or replace if necessary.

Defective main
PCB or fax control
PCB.

Replace the main PCB or fax control PCB
and check for correct operation.

C0880

Fax control PCB*

program archive

problem

When power is turned on, the com-
pressed program in the Flash ROM on
the fax control PCB was not successfully
decompressed.

Defective fax con-
trol PCB.

Replace the fax control PCB and check for
correct operation.

*1: Optional. *2: Optional for 16 ppm model. Standard for 20 ppm model.

Code

Contents

Remarks

Causes

Check procedures/corrective measures

Summary of Contents for KM-1650

























































































































































































































































































Search results

Summary of Contents for KM-1650

Reviews:

Brands by name

Popular brands

Kyocera KM-1650, Service Manual

Search results

Summary of Contents for KM-1650

Reviews:

Brands by name

Popular brands