manualshive.com logo in svg

Kyocera KM-1650, Service Manual

Share
Download
Kyocera KM-1650 Service Manual Download Page 76

2DA/2DB

1-4-7

U005

Copying without paper
Description

Simulates the copy operation without paper feed. 

Purpose

To check the overall operation of the machine. 

Method

1. Press the start key. The screen for selecting an item is displayed.
2. Select the item to be operated using the up/down cursor keys. The selected item is displayed in reverse.

3. Press the interrupt key. The copy mode screen is displayed.
4. Set the operation conditions required on the copy mode screen. Changes in the following settings can 

be made.
Paper feed locations
Magnifications
Simplex or duplex copy mode
Number of copies: in simplex copy mode, continuous copying is performed when set to 999; in duplex 
copy mode, continuous copying is performed regardless of the setting.
Copy density
Keys on the operation panel other than the energy saver (preheat) key

5. To control the paper feed pulley, remove all the paper in the drawers, or the drawers. With the paper 

present, the paper feed pulley does not operate.

6. Press the start key. The operation starts.

Copy operation is simulated without paper under the set conditions. When operation is complete, the 
screen for selecting an item is displayed.

7. To stop continuous operation, press the stop/clear key.

Completion

Press the stop/clear key at the screen for selecting an item. The screen for selecting a maintenance item No.
is displayed.

Maintenance

item No.

Description

Display

Operation

PPC

Only the MFP operates.

PPC + DP

Both the MFP and DP operate (continuous operation).

Summary of Contents for KM-1650

























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands