KYMCO Downtown 350i Repair Manual Download Page 262 | Manualshive

Page: 262 / 616

background image

4.Engine

Downtown 350i

4-88

Crankshaft Inspection

Check the side clearance of the big end of the connecting rod with a feeler
gauge.

Item

Standard (mm)

Service Limit (mm)

Crankshaft

Connecting rod big

end side clearance

0.15 - 0.35

0.6

Grip the small end of the connecting rod and try and push the rod down towards
the crank weights. If there is definite play between the connecting rod and crank
the crankshaft should be replaced.

«
...
260
261
262
263
264
...
»

Summary of Contents for Downtown 350i









































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Downtown 350i

Brand: ACERBIS Pages: 72

Brand: Memphis Shades Pages: 2

Brand: R&G Pages: 8

Power Commander III 718-411

Brand: Dynojet Pages: 3

Brand: X-lite Pages: 136

Lock-it TANKRING 506003

Brand: hepco & becker Pages: 2

Brand: BMW Motorrad Pages: 231

Brand: Clas Ohlson Pages: 5

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 124

ROAD STAR XV16A

Brand: Yamaha Pages: 117

X MAX CZD300P 2022

Brand: Yamaha Pages: 142

Brand: Yamaha Pages: 97

Brand: Yamaha Pages: 119

Brand: Yamaha Pages: 96

Brand: Faller Pages: 8

Brand: VESPA Pages: 249

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands