manualshive.com logo in svg

KYMCO Downtown 350i, Repair Manual, Page: 100 / 616

Share
Download
KYMCO Downtown 350i Repair Manual Download Page 100

2.Periodic Maintenance 

Downtown 350i 

 

 

2-65 

 

 

Place a 9 mm box end wrench over the locknut, and loosen the locknut. If the 
valve clearance is tight back out the valve tappet adjusting screw with the tappet 
adjustment tool. If the clearance is too loose turn in the adjusting screw until there 
is a light drag on the feeler gauge. Hold the adjusting screw locknut in place with 
the wrench to make sure it doesn't interfere with the adjustment. 
  
Lubricate the tappet adjusting screw threads with fresh engine oil. Hold the 
adjuster in place and tighten the locknut. Always recheck the clearance after 
tightening the locknut. Also, recheck after turning the engine over and back to 
TDC on the compression stroke. 
  

   Item 

Qty 

Thread  

size (mm) 

Torque 

   Remarks 

kgf-m 

lb-ft 

Valve adjusting lock nut 

4 

5 

0.7-1.1  5.06-7.96 

Apply oil to thread 

 

 

Summary of Contents for Downtown 350i









































































































































































































































































































































































































































































































































































































































Reviews:

No comments