KYMCO Downtown 350i Repair Manual Download Page 48 | Manualshive

Page: 48 / 616

background image

2.Periodic Maintenance

Downtown 350i

2-13

Brake Inspection

SAFETY FIRST: Protective gloves and eyewear are recommended at this
point.

Brake Lever Adjuster

There is adjuster on each brake lever. Each adjuster has four positions so that
the released lever position can be adjusted to suit the rider’s hands.To adjust the
distance of the lever from the handlebar grip, push the lever forward and turn the
adjuster knob to align the number with the arrow mark on the lever holder.

«
...
46
47
48
49
50
...
»

Summary of Contents for Downtown 350i









































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Downtown 350i

Versaflo M Series

Brand: 3M Pages: 27

Speedglas 9100 Series

Brand: 3M Pages: 2

Brand: 3M Pages: 5

Brand: R&G Pages: 12

Brand: Qlink Pages: 44

Brand: Graphite Pages: 44

Brand: GAS GAS Pages: 57

Zero S Series 2014

Brand: Zero Motorcycles Pages: 128

Windscreen N20012A

Brand: VStreamT Pages: 3

Brand: Honda Pages: 143

Brand: Honeywell Pages: 93

Brand: Hudora Pages: 8

Brand: hepco & becker Pages: 3

Brand: SUR-RON Pages: 37

Brand: GÜDE Pages: 80

Brand: GÜDE Pages: 88

Brand: Sealey Pages: 4

Brand: Power Fist Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands