KYMCO Downtown 350i Repair Manual Download Page 205

Page: 205 / 616

4.Engine

Downtown 350i

4-31

Valves

SAFETY FIRST: Protective gloves and eyewear are recommended at this
point.

Removal

Remove the camshaft. See the

Camshaft

topic for more information.

Remove the cylinder head. See the

Cylinder Head

topic for more information.

IMPORTANT:

Record the position of all parts so they can be returned to their

proper place during reassembly.

Push down the valve springs with a valve spring compressor.
Special Tool- Valve Spring Compressor: E040

Remove the split keepers. There are two per valve.

Summary of Contents for Downtown 350i









































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Downtown 350i

Reviews:

Related manuals for Downtown 350i

Brands by name

Popular brands

KYMCO Downtown 350i, Repair Manual

Search results

Summary of Contents for Downtown 350i

Reviews:

Related manuals for Downtown 350i

Brands by name

Popular brands