KYMCO Downtown 350i Repair Manual Download Page 533

Page: 533 / 616

10..Brake System

Downtown 350i

8-55

ABS Motor Relay Inspection (service code 35)

1st step test.

Check the ABS motor relay fuse (25A).

Front Wheel Rotation Sensor Signal Abnormal (service

code 42)

1st step test.

Measure the clearance between the front wheel rotation sensor and sensor rotor.

Standard: 1 mm (0.04 in.)

If the measurement is over standard, check each part for deformation and looseness and

correct accordingly. Recheck the clearance.

Check that there is iron or other magnetic deposits between the sensor

and sensor rotor, and the sensor rotor slots for obstructions.

Check the installation condition of the sensor for looseness.

Check the sensor and sensor rotor tip for deformation or damage (example chipped sensor

rotor teeth).

Summary of Contents for Downtown 350i









































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Downtown 350i

Reviews:

Related manuals for Downtown 350i

Brands by name

Popular brands

KYMCO Downtown 350i, Repair Manual

Search results

Summary of Contents for Downtown 350i

Reviews:

Related manuals for Downtown 350i

Brands by name

Popular brands