KYMCO Downtown 350i Repair Manual Download Page 414

Page: 414 / 616

8.Final Drive

Downtown 350i

8-8

Final Reduction

SAFETY FIRST: Protective gloves and eyewear are recommended at this
point.

Disassembly

Note:

Do not remove the transmission case cover except for necessary part

replacement. If the drive shaft is replaced, make sure to also replace the bearing
and oil seal.

Remove the belt case. See the

Belt Case

topic for more information.

Remove the CVT belt and pulleys. See the

CVT Removal

topic for more

information.

Drain the final drive oil. See the

Final Drive Oil

topic for more information.

Remove the rear wheel. See the

Rear Wheel

topic for more information.

There are 9 transmission case cover bolts.

Summary of Contents for Downtown 350i









































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Downtown 350i

Reviews:

Related manuals for Downtown 350i

Brands by name

Popular brands

KYMCO Downtown 350i, Repair Manual

Search results

Summary of Contents for Downtown 350i

Reviews:

Related manuals for Downtown 350i

Brands by name

Popular brands