KYMCO Downtown 350i Repair Manual Download Page 550 | Manualshive

Page: 550 / 616

background image

11.Steering

Downtown 350i

11-8

Steering Stem Removal

SAFETY FIRST: Protective gloves and eyewear are recommended at this
point.

Support the vehicle with a suitable stand or jack so that the front wheel is off the
ground. Grip the bottom of the fork legs and turn the front end side-to-side. If the
movement is rough the bearings should be greased or replaced. If the movement
is to tight or loose the steering stem adjusting nut may need to be adjusted.

The KYMCO Downtown 350i uses ball bearings in the steering. Always replace
the races at the same time as the bearings.

Remove the handlebar covers. See the

Handlebar Covers

topic for more

information.

Remove the front cover. See the

topic for more information.

Remove the handlebar. See the

topic for more information.

Remove the front fender. See the

topic for more information.

Remove the front wheel. See the

topic for more information.

Remove the front fork. See the

Front Fork Removal and Installation

topic for

more information.

«
...
548
549
550
551
552
...
»

Summary of Contents for Downtown 350i









































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Downtown 350i

Brand: Caberg Pages: 3

Brand: Caberg Pages: 2

Brand: Uclear Pages: 2

Brand: Öhlins Pages: 8

Brand: AFX Pages: 52

Freeride 350 AUS

Brand: KTM Pages: 25

Brand: R&G Pages: 9

Brand: UBCO Pages: 27

SHERCO 50 SE 2022

Brand: SHERCO Pages: 226

Brand: Yamaha Pages: 287

Brand: Yamaha Pages: 109

Brand: DYNATEK Pages: 8

Brand: DYNATEK Pages: 6

Brand: Aim Pages: 47

2007 PAMPERA 125

Brand: GAS GAS Pages: 58

Brand: Hama Pages: 22

Brand: Saddlemen Pages: 2

Brand: Saddlemen Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands