Kurabo QuickGene-Auto240L Operation Manual Download Page 15

Page: 15 / 78

1 System Installation Procedures

QuickGene-Auto240L Operation Manual

1 System Installation Procedures

The installation procedures for this system are explained below.

1.1 Conditions for Installation, Operating Environment

The conditions for system installation and the operating environment are explained here.

■ Conditions for Installation

・

Do not install this system where water may be poured or spilt, which may

failure, fire or electric shock.

・

Be sure to remove the power plug from the outlet whenever this system is

moved. Watch your step carefully while operating. Injury, fire or electric

may result from a damaged power cable.

・

Do not install this system in a location with intense vibration or at an unstable

incline. This may cause injury or failure.

・

Do not install this system in a location exposed to direct sunlight or in the

proximity of a heating or cooling appliance. This may cause a shortened

lifetime or failure.

Please install this system in an indoor location as shown below for normal, safe use.

・

A location with the following secure space for installation.

Required footprint: Width

≧

178 cm × Depth

≧

152 cm × Height

≧

205 cm (when placed on an

80-cm high experiment table)

Warning

Caution:

10cm

(40 cm)

(20 cm)

(10 cm)

(70 cm)

(10 cm)

205 cm

178 cm

152 cm

Summary of Contents for QuickGene-Auto240L















































































Search results

Summary of Contents for QuickGene-Auto240L

Reviews:

Brands by name

Popular brands

Kurabo QuickGene-Auto240L, Operation Manual

Search results

Summary of Contents for QuickGene-Auto240L

Reviews:

Brands by name

Popular brands