KUHN RW1600 Operation Manual Download Page 85

Page: 85 / 102

Maintenance

Wheels/tyres

Do not drive with worn-out or damaged tyres

Exchange worn-out or damaged tyres immediately. Especially during
road transport with such tyres an increased risk of accidents exists.

Correct repairwork only

Repairwork on wheels and tyres must only be carried out

•

by professionals

•

with the correct fitting equipment

Mounting wheels and tyres requires sufficient knowledge and
availability of prescribed tools and equipment being in perfect
condition. Serious personal injuries or machine damages can occur.

Tyre dimensions as described

Do not fit other tyre dimensions than prescribed. Fitting other tyre
dimensions can cause accidents. Personal injuries or machine
damages can occur.

Pre-scribed tyre pressure only

Only use the pre-scribed tyre pressure. Using the wrong tyres
pressure can cause serious personal injuries, machine damages or
traffic accidents.

When working on the wheels and tyres make sure that the machine

•

has been placed on the ground safely (use support jack)

•

is secured by chocks against unintentional rolling

Tyre pressure

Check the tyre pressure regularly

•

once a day

•

before every road transport

•

before and after every season

Tyre size

Tyre pressure (bar)

15.0/55-17

1.5

Summary of Contents for RW1600







































































































Search results

Summary of Contents for RW1600

Reviews:

Related manuals for RW1600

Brands by name

Popular brands

KUHN RW1600, Operation Manual

Search results

Summary of Contents for RW1600

Reviews:

Related manuals for RW1600

Brands by name

Popular brands