Kramer Electronics Ltd.
VP-440X
– Protocol 3000
60
Function Description
Syntax
Parameters/Attributes
Example
CEC
Set display to ON./OFF
COMMAND
#CEC
state
<CR>
FEEDBACK
~nn@CEC
state
OK
<CR><LF>
state
– CEC state
0
– Off
1
– On
Set display to ON via CEC:
#CEC ON
<CR>
CEC-PASS
Set display ON/OFF.
COMMAND
#CEC-PASS
state
<CR>
FEEDBACK
~nn@CEC-PASSw
state
<CR><LF>
state
– CEC state
0
– Off
1
– On
Set display status to off:
#CEC-PASS
0
<CR>
CEC-PASS?
Get display status.
COMMAND
#CEC-PASS?
<CR>
FEEDBACK
~nn@CEC-PASS
state
<CR><LF>
state
– CEC state
0
– Off
1
– On
Get display status:
#CEC-PASS?
<CR>
DISPLAY?
Get output HPD status.
COMMAND
#DISPLAY?
out_index
<CR>
FEEDBACK
~nn@DISPLAY
out_index
,
status
<CR><LF>
out_index
– Number that indicates
the specific output:
1
– HDMI
2
– HDBT
status
– HPD status according to
signal validation
0
– Signal or sink is not valid
1
– Signal or sink is valid
2
– Sink and EDID is valid
Get the output HPD status of
HDMI output:
#DISPLAY?
1
<CR>
DPSW-STATUS?
Get the DIP-switch state.
COMMAND
#DPSW-STATUS?
dip_id
<CR>
FEEDBACK
~nn@DPSW-STATUS
dip_id
,
status
<CR><LF>
dip_id
– 0
status
– Up/down
0
– Up
1
– Down
get the DIP-switch status:
#DPSW-STATUS?
0
<CR>
EQ-LVL
Set equalization level.
COMMAND
#EQ-LVL
io_mode
,
eq_type
,
eq_level
<CR>
FEEDBACK
~nn@EQ-LVL
io_mode
,
io_index
,
eq_type
,
eq_level
<CR><LF>
io_mode
– 1
eq_type
– Equalizer Types [Hz]:
120
200
500
1200
3000
7500
12000
eq_level
– Equalizer level (-10dB to
10dB):
0 to 40
Set 200Hz EQ level to 12:
#EQ-LVL
1
,
200
,
12
<CR>
EQ-LVL?
Get equalization level.
COMMAND
#EQ-LVL?
io_mode
,
io_index
,
eq_type
<CR>
FEEDBACK
~nn@EQ-LVL
io_mode
,
io_index
,
eq_type
,
eq_level
<CR><LF>
io_mode
– 1
eq_type
– Equalizer Types [Hz]:
120
200
500
1200
3000
7500
12000
eq_level
– Equalizer level (-10dB to
10dB):
0 to 40
Get 120Hz EQ level:
#EQ-LVL?
1
,
120
<CR>
ETH-PORT
Set Ethernet port protocol.
If the port number you
enter is already in use, an
error is returned.
The port number must be
within the following range:
0-(2^16-1).
COMMAND
#ETH-PORT
port_type
,
port_id
<CR>
FEEDBACK
~nn@ETH-PORT
port_type
,
port_id
<CR><LF>
port_type
– TCP/UDP
port_id
– TCP/UDP port number
(0
– 65535)
Set the Ethernet port protocol
for TCP to port 12457:
#ETH-PORT
0
,
12457
<CR>
ETH-PORT?
Get Ethernet port protocol.
COMMAND
#ETH-PORT?
port_type
<CR>
FEEDBACK
~nn@ETH-PORT
port_type
,
port_id
<CR><LF>
port_type
– TCP/UDP
TCP
UDP
port_id
– TCP / UDP port number (0
– 65535)
Get the Ethernet port protocol
for UDP:
#ETH-PORT?
1
<CR>
FACTORY
Reset device to factory
default configuration.
This command deletes
all user data from the
device. The deletion can
take some time.
Your device may require
powering off and powering
on for the changes to take
effect.
COMMAND
#FACTORY
<CR>
FEEDBACK
~nn@FACTORY
ok
<CR><LF>
Reset the device to factory
default configuration:
#FACTORY
<CR>