Korenix JetNet 4706 User Manual Download Page 58

 

JetNet 4706/4706f Industrial Managed PoE Switch   

54

Link Type - P2P 

Switch(config-if)# spanning-tree link-type point-to-point 

Link Type – Share 

Switch(config-if)# spanning-tree link-type shared 

Edge Port 

Switch(config-if)# spanning-tree edge-port enable 
Switch(config-if)# spanning-tree edge-port disable 

RSTP Info

 

Active status 

Switch# show spanning-tree active 

Rapid Spanning-Tree feature               Enabled 

Spanning-Tree BPDU transmission-limit     3 

Root Address     0012.7701.0386   Priority 4096 

Root Path Cost : 200000           Root Port : 7 

Root Times :      max-age 20 sec, hello-time    2 sec, forward-delay 15 sec 

Bridge Address   0012.77ff.0102   Priority 4096 

Bridge Times : max-age 10 sec, hello-time    2 sec, forward-delay 15 sec 

Aging time : 300 

Port              Role            Port-State          Cost            Prio.Nbr            Type 

-------  ----------  ------------  ---------  ----------  ----------- 

 fa6    Designated  Forwarding      200000     128.6      Auto(RST) 

 fa7    Root        Forwarding      200000     128.7      

Shared(STP)

 

RSTP Summary 

Switch# show spanning-tree summary 

Switch is in rapid-stp mode. 

BPDU skewing detection disabled for the bridge. 

Backbonefast disabled for bridge. 

Summary of connected spanning tree ports : 

#Port-State Summary 

Blocking  Listening  Learning  Forwarding  Disabled 

--------  ---------  --------  ----------  -------- 

            0                    0                  0                      2                  8 

#Port Link-Type Summary 

AutoDetected   PointToPoint   SharedLink   EdgePort 

------------   ------------   ----------   -------- 

                    9                            0                        1                    9

 

Port Info 

Switch# show spanning-tree port detail fa7    (Interface_ID) 

Rapid Spanning-Tree feature               Enabled            

IEEE compatible Spanning-Tree Protocol    Enabled  

Spanning-Tree BPDU transmission-limit     3  

Bridge identifier has priority 4096, address 0012.77ff.0102   

Configured hello time 2, max age 10, forward delay 15   

Current root has priority 4096, address 0012.7701.0386   

Root port is 7 , cost of root path is 200000   

Topology change flag not set, detected flag not set 

Number of topology changes 0, last change occurred from 0000.0000.0000   

Times:    hello 2 , max age 20 , forward delay 15   

Timers: hello 0 , topology change 0   

Rapid Spanning-Tree link-type : Shared   

Rapid Spanning-Tree edge-port : Disabled   

Port 128.7 as Root Role is in Forwarding State   

Port Path Cost 200000, Port Identifier 128.7   

Designated root has priority 4096, address 0012.7701.0386   

Designated bridge has priority 4096, address 0012.7701.0386   

Designated Port ID is 128.1, Root Path Cost is 0   

Timers : message-age 4 sec, forward-delay 0 sec   

Forwarding-State Transmit count   2  

BPDU: sent 624 , received 3600   

Summary of Contents for JetNet 4706





































































































Reviews: