manualshive.com logo in svg

Korenix JetNet 4706, User Manual

Share
Download
Korenix JetNet 4706 User Manual Download Page 38

 

JetNet 4706/4706f Industrial Managed PoE Switch   

34

Click 

OK.

 The system will then automatically reboot the device. 

Note:

 If you have already configured the IP of your device to another IP address; when you 

use this command through CLI and Web UI, our software will not reset the IP address to 
the default IP. The system will maintain the IP address so that you can still connect to the 
switch via the network.   

 

4.2.9 System 

Reboot 

System Reboot allows you to reboot the device. Some of the feature changes require you 
to reboot the system. Click the 

Reboot

 button to reboot your device. 

Note: 

Remember to click the 

Save 

button to save your settings. Otherwise, the settings 

you made will be gone once the switch is powered off. 

 

Below is the Main screen for Reboot 

 

 

Below is the popup alert screen to request confirmation for the Switch Reboot. Click 

Yes

 to 

reboot the switch. 

 

 

The popup message screen below appears when rebooting the switch. 

 

 

 

Summary of Contents for JetNet 4706





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands