manualshive.com logo in svg

Korenix JetNet 4508 V2 Series, User Manual

Share
Download
Korenix JetNet 4508 V2 Series User Manual Download Page 46

 

42

 

4.2.7 Firmware Upgrade 

In this section, you can update the latest firmware for your switch. Korenix 
provides the latest firmware in Korenix Web site. The new firmware may include 
new features, bug fixes or other software changes. We’ll also provide the 
release notes for the update as well. For technical viewpoint, we suggest you 
use the latest firmware before installing the switch to the customer site. 

Note: the system will automatically reboot after you finished upgrading 
new firmware. Please remind the attached users before you do that. 

Figure 4.2.7.1 Main UI of Firmware Upgrade

 

 

      Sample of JetNet 5010G firmware upgrade 

 

There are 2 modes for users to backup/restore the configuration file, Local File 
mode and TFTP Server mode. 

Local File

 mode: In this mode, the switch acts as the file server. Users can 

browse the target folder and then type the file name to backup the configuration. 
Users also can browse the target folder and select the existed configuration file 
to restore the configuration back to the switch. This mode is only provided by 
Web UI while CLI is not supported. 

TFTP Server

 mode: In this mode, the switch acts as the TFTP client. Before 

you do so, make sure that your TFTP server is ready. And then please type the 
IP address of TFTP Server IP address. This mode can be used in both CLI and 
Web UI. 

TFTP Server IP Address

: You need to key in the IP address of your TFTP 

Server here. 

Summary of Contents for JetNet 4508 V2 Series







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands