Korenix JetNet 4508 V2 Series User Manual Download Page 130

Page: 130 / 134

126

-40

℃

~75

℃

(JetNet 4508-w V2/JetNet 4508f-w V2)

Operating Humidity

0% ~ 90%, non-condensing

Storage Temperature

-40

℃

~ 85

℃

Hi-Pot Insulation

AC 1.5KV for all ports and power

Regulatory
Approvals

EMC

IEC 61000-6-2, IEC 61000-6-4.

EMI

FCC Class A, CE/ EN55022

Radiation, Conduction

EMS

IEC 61000-4-2, IEC 61000-4-3, IEC 61000-4-4, IEC 61000-4-5, IEC

61000-4-6, IEC 61000-4-8, IEC 61000-4-9

Vibration

IEC60068-2-6

Note-2

Shock

IEC60068-2-27

Note-2

Free Fall

IEC60068-2-32 with package

Note-3

Warranty

Global 5 years

Note-1: Available in the further version software.

Note-2: pending
Note-3: Korenix’s internal testing

Note-4: For the latest version specification, please contact your sales window or distributor.

Summary of Contents for JetNet 4508 V2 Series







































































































































Search results

Summary of Contents for JetNet 4508 V2 Series

Reviews:

Brands by name

Popular brands

Korenix JetNet 4508 V2 Series, User Manual

Search results

Summary of Contents for JetNet 4508 V2 Series

Reviews:

Brands by name

Popular brands