manualshive.com logo in svg

Kontron KISS 4U V3, User Manual

Share
Download
Kontron KISS 4U V3 User Manual Download Page 26

KISS 4U V3 SKX – Preliminary Rev. 0.6 

 

www.kontron.com 

  

// 26 

 

4.1.8.

 

Drive Bays 

The drive bay can be a mixture of front accessible and internal drives, with a maximum of eight drives. The drive bays 
D1, D2 and D3 are accessible on the front panel or internally accessible. D1 and D2 drive bay can be fitted with 
removable, fixed or internal drives and may be used in combination to implement a three-drive solution. 

Front accessible drive option: 

 

D1: 1x 3.5" HDD or 2x 2.5" HDD/SSD or 4x 2.5" HDD/SSD  

 

D2: 1x 3.5" HDD or 2x 2.5" HDD/SSD or 4x 2.5“HDD/SSD  

 

Combined D1 and D2: 2x 3.5”HDD or 3x  3.5” HDD  

 

D3: 1x DVD (RW slimline) 

Internal drive options: 

 

D1: 3.5” HDD 

 

D2: 3.5” HDD 

 

D4: 1x 2.5" HDD/SSD or 2x 2.5" HDD/SSD or 1x 3.5” HDD 

For more information on the possible drive bay combinations and the drive bay capacity, see Chapter 5.2: Drive Bays. 

Summary of Contents for KISS 4U V3









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands