Kongsberg EM 710
3
Close the top of the steel conduits with a seal.
• Kongsberg Maritime recommends the use of sealing from
Roxtec, Bratberg or similar. This system is described in
the Appendices chapter in this manual.
4.5 Installing the mounting frames
Mounting frames are designed to house the individual transducer
modules.
A mounting frame is normally required for the 0.5 degree
transmit transducer as it consists of two separate modules. This
should not be necessary for the other transducer models. These
are self-contained units and due to their internal (very strong)
carbon-fibre structures, they may be bolted directly to a flat
mounting plate (for example).
While the transducer modules are mounted into the frames,
the frames require casings. The casings must be individually
designed for each vessel, and it is not a part of the system
delivery. The casings must therefore both be provided (or
manufactured) and installed by the installation shipyard.
The installation must be carried out according to arrangement
drawings designed for the specific vessel. Refer to the drawings
included in the Drawing File, and the applicable drawings
prepared by the installation shipyard.
4.5.1 Logistics and references
Safety
- Refer to the general safety procedures. Note that the
units are heavy !
Personnel
- Trained mechanical workers
Ship location
- Dry dock
Special tools
- None
Drawings
- Refer to the previously mentioned drawings in the
Drawing File.
1° mounting frame assembly RX module
on page 112
2° mounting frame assembly TX/RX module
on page 114
4.5.2 Procedures
Note
The mounting frames must be handled with care. Please observe
normal safety precautions for dockyard work and welding.
1
Manufacture the casings according to the attached
production drawing.
38
164851/C
Summary of Contents for EM 710
