Komatsu D65EXi-18, Operation & Maintenance Manual

Page: 181 / 184

INDEX
Symbols
3DMC....................................................................4-68
3DMC - Exit ..........................................................4-31
3DMC information - Display.................................. 4-68
A
Actions when automatic blade control is activated.......
.......................................................................3-37
Actions when message is displayed on control box.....
.......................................................................3-73
Actions when pop-up message is displayed on con-
trol box........................................................... 3-76
Active alignment file - Select.................................4-30
Active file...............................................................4-30
Active surface file - Select.....................................4-30
Adjust blade elevation...........................................4-41
Adjust blade wear amount.................................... 4-41
Alignment display - Set......................................... 4-62
As-built control options - Set................................. 4-33
As-built surface display - Add............................... 4-33
As-built surface display - Delete........................... 4-36
As-built surface display - Set................................ 4-64
Ative as-built view - Select.................................... 4-31
Auto-pitch adjustment........................................... 3-14
Auto/Manual switch.................................................3-7
Automatic best-fit blade control - Set.................... 4-38
B
Back grade mode - Handle................................... 3-38
Back grade mode switch....................................... 3-11
Back grade work................................................... 3-64
Background color display - Set............................. 4-66
Battery disconnect switch - Turn off before long-term
storage...........................................................3-70
Before reading this manual..................................... 1-2
Blade - Activate automatic control........................ 3-35
Blade - Adjust elevation........................................ 3-34
Blade - Change lower edge position in cutting in..3-47
Blade - Check / Adjust elevation........................... 3-27
Blade - Check elevation........................3-27,3-29,3-32
Blade - Control automatically................................ 3-22
Blade - Handle automatic control..........................3-35
Blade - Operate to travel reverse in automatic control.
.......................................................................3-38
Blade - Set dozing mode.......................................3-43
Blade - Set load mode.......................................... 3-44
Blade - Stop automatic control..............................3-41
Blade control......................................................... 4-38
Blade edge - Set standard angle.................. 3-19,3-27
Blade edge and track shoe - Input wear amount.. 3-25
Blade elevation - Check........................................ 4-43
Blade load selection..............................................4-72
C
Calibrate blade position........................................ 4-41
Carry and compact soils....................................... 3-55
Carry soils to hole................................................. 3-54
Checks and adjustment before starting engine.....3-16
Checks before starting.......................................... 3-26
Component which contains mercury - Handle........ 2-6
Control box..............................................................3-6
Control box - Set for connecting to machine.........4-32
Control box name....................................................3-5
Control menu........................................................ 4-32
Control point files.................................................. 4-12
Control point files - Import.....................................4-12
Controls and gauges names................................... 3-4
Crown road surface files - Create......................... 4-24
Cut/fill offsets - Adjust................................... 4-77,4-80
Cut/fill offsets switch............................................. 3-10
Cutting and carry operation...................................3-54
Cylinder - Reset stroke end.......................... 3-17,3-26
D
Display extended status text in plan/profile/section.....
.......................................................................4-79
Display options......................................................4-61
Display options - Display.......................................4-61
Displayed units - Set............................................. 4-66
Dozing control....................................................... 4-41
Dozing mode selection..........................................4-72
E
Elevation control key.............................................4-69
Engine - Stop........................................................ 3-20
Exit 3DMC.............................................................4-31
Explanation of components.....................................3-6
F
File menu................................................................ 4-7
Finishing operation of bank soil............................ 3-65
Flat surface files - Create......................................4-20
Function related with machine monitor blade auto-
matic control.................................................. 3-48
G
Gain of automatic blade control - Adjust............... 3-48
General precautions common to operation and main-
tenance............................................................ 2-3
General view........................................................... 3-2
GNSS antenna......................................................3-13
GNSS information - Display.................................. 4-75
GNSS radio device............................................... 3-13
GNSS receiver...................................................... 3-14
INDEX
6-1