
Section 4 -- Disassembly/Reassembly
4-73
2005 July Rev. B 7F3318
12. After ghosting, upload the system configuration file from FLOPPY DRIVE to the HARD DRIVE.
Removing the CD-ROM Drive
4 SCREWS
SIGNAL
CABLES
POWER
CABLES
HARD
CD-ROM
FLOPPY
DRIVE
DRIVE DRIVE
2 Spring-loaded SCREWS
2 SLOTS
SCREW
SCREW
BRACKET
JUMPER
Figure 4-57. Removing the CD-ROM DRIVE
1. Disconnect the POWER CABLE and SIGNAL CABLE from the HARD DRIVE (see Figure 4-55).
2. Disconnect the POWER CABLE from the CD-ROM DRIVE.
3. Loosen 2 spring-loaded SCREWS.
!
Caution
Take care not to damage CONNECTORS of the CABLES that are still attached during the removal.
4. Slide the assembly of the 3 DRIVES slightly back from the front of the COMPUTER and carefully lift to
remove the assembly with CABLES still attached to the CD-ROM DRIVE and FLOPPY DRIVE.
5. Disconnect the SIGNAL CABLE from the CD-ROM DRIVE.
6. Remove 2 SCREWS fastening the CD-ROM DRIVE to the BRACKET.
7. Slide the CD-ROM DRIVE out of the BRACKET.
8. Check that the JUMPER on the new CD-ROM DRIVE is set at the “MASTER” position.
Note
Fold CABLES neatly under the DRIVES during reassembly.
9. Install the new DRIVE in reverse order of the disassembly procedure.
4-14-2. Removing the FLOPPY DRIVE
1. Repeat steps 1 through 5 of “Removing the CD-ROM DRIVE”.
2. Disconnect the POWER CABLE and SIGNAL CABLE from the FLOPPY DRIVE.
3. Remove 2 SCREWS fastening the FLOPPY DRIVE to the BRACKET.
4. Slide the FLOPPY DRIVE out of the BRACKET.
Note
Fold CABLES neatly under the DRIVES during reassembly.
Summary of Contents for DryView 8150
