Knauer AZURA P 2.1S User Manual Download Page 3

Page: 3 / 47

Table of Contents

P 2.1S/P 4.1S user manual V6870, version 3.1

Table of Contents

Note:

For your own safety,

read

the manual and

always

observe the warnings

and safety information on the device and in the
manual!

Intended Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Device Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Pump Heads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Eluents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Scope of Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Signal Words . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Decontamination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Symbols and Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Unpacking and Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Contacting the Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Location Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Connecting the Eluent Line to the Pump Head . . . . . . . . . . . . . . . . . . . .

Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Pin Header for Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Computer Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Configuring the LAN Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Connecting the Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Configuring the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Integrating the LAN into a Company Network . . . . . . . . . . . . . . . . . .

Controlling Several Systems Separately in a LAN . . . . . . . . . . . . . . . .

Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Switching on the Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Selecting the Pump Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Flushing the Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Summary of Contents for AZURA P 2.1S
















































Search results

Summary of Contents for AZURA P 2.1S

Reviews:

Related manuals for AZURA P 2.1S

Brands by name

Popular brands

Knauer AZURA P 2.1S, User Manual

Search results

Summary of Contents for AZURA P 2.1S

Reviews:

Related manuals for AZURA P 2.1S

Brands by name

Popular brands