Knauer AZURA P 2.1S User Manual Download

Page: 9 / 47

Scope of Delivery

P 2.1S/P 4.1S user manual V6870, version 3.1

Scope of Delivery

Note:

Only use original parts and accessories made by KNAUER or a company

authorized by KNAUER.



Pump P 2.1S/P 4.1S



User manual



Power adapter 24 V



Installation Qualification Document



Accessories Kit Pump



Accessories Kit AZURA

Safety

Professional Group

The user manual addresses persons who are qualified as chemical laboratory
technicians or have completed comparable vocational training.

The following knowledge is required:



Fundamental knowledge of liquid chromatography



Knowledge regarding substances that are suitable only to a limited extent for
use in liquid chromatography



Knowledge regarding the health risks of chemicals



Participation during an installation of a device or a training by the company
KNAUER or an authorized company.

If you do not belong to this or a comparable professional group, you may not
perform the work described in this user manual under any circumstances. In this
case, please contact your superior.

Safety Equipment

When working with the device, take measures according to lab regulations and
wear protective clothing:



Safety glasses with side protection



Protective gloves



Lab coat



Dilute acetic acid (10-50%), at 25° C/77.0° F



Dilute sodium hydroxide (1M)



Water

1. valid for the specified temperature range

Suitable eluents

Summary of Contents for AZURA P 2.1S
















































Search results

Summary of Contents for AZURA P 2.1S

Reviews:

Related manuals for AZURA P 2.1S

Brands by name

Popular brands

Knauer AZURA P 2.1S, User Manual

Search results

Summary of Contents for AZURA P 2.1S

Reviews:

Related manuals for AZURA P 2.1S

Brands by name

Popular brands