Knauer AZURA P 2.1S User Manual Download

Page: 30 / 47

Operation

P 2.1S/P 4.1S user manual V6870, version 3.1

Starting with a Short-Circut

Connection for the short circuit (or TTL-low) for interrupting and continuing the
operation of the pump.

The operation of the pump is dependent on the

STARTLEVEL setting:



STARTLEVEL 1

(standard setting RS-232, LAN)

: The pump does not operate

during the time of short-circuit.



STARTLEVEL 0

(standard setting Analog)

: The pump operates during the time

of short-circuit.

Enter

STARTLEVEL:1

in the terminal program,

to stop the pump during short-cir-

cuit

Prerequisite:

The pump is connected to the power supply.

Note:

During the interruption, the horizontal arrow remains in the display,

because the pump is still in operation status.

Process:

1. Connect the pump to a suitable terminal program.
2. Connect the pump using a LAN or RS-232.
3. Enter

STARTLEVEL:1

Starting Directly after Connecting to Power Supply

By default the pump is stopped and started using the start/stop button. The
STARTMODE setting allows you to start the device right after connecting it to
power supply.



STARTMODE 0

(default setting RS-232, LAN)

: The pump does not start operat-

ing right after being connected to power supply.



STARTMODE 1

(default setting Analog)

: The pump starts operating right after

being connected to power supply.

Enter in the terminal program using RS-232

STARTMODE:1

, so that the pump is

in operation directly after being connected to the power supply.

Prerequisite:

The pump is connected to the power supply.

Process:

1. Connect the pump to a suitable terminal program.

Fig. 23

Status display

Legend

Pressure in 0,1 MPa

Flow rate in ml/min

Summary of Contents for AZURA P 2.1S
















































Search results

Summary of Contents for AZURA P 2.1S

Reviews:

Related manuals for AZURA P 2.1S

Brands by name

Popular brands

Knauer AZURA P 2.1S, User Manual

Search results

Summary of Contents for AZURA P 2.1S

Reviews:

Related manuals for AZURA P 2.1S

Brands by name

Popular brands