KMB NOVAR 2600, Operating Manual

Page: 3 / 96

NOVAR 2600 Operating Manual
4.3 PFC Setup Parameters.............................................................................................................................. 24
4.3.1 PFC Control Setup............................................................................................................................... 25
4.3.1.1 Target Power Factor for Tariff 1/2.................................................................................................25
4.3.1.2 Control Bandwidth on High Loads for Tariff 1/2............................................................................25
4.3.1.3 Control Time for Tariff 1/2............................................................................................................. 26
4.3.1.4 Offset Power for Tariff 1/2........................................................................................................... 27
4.3.1.5 Tariff 2 Control............................................................................................................................. 27
4.3.1.6 Tariff 2 Control Power.................................................................................................................. 28
4.3.1.7 Control Strategy........................................................................................................................... 28
4.3.1.8 Choke Control.............................................................................................................................. 29
4.3.1.8.1 Mixed Choke Control............................................................................................................. 29
4.3.1.8.2 Non-Mixed Choke Control.....................................................................................................30
4.3.1.9 Choke Control Limit Power Factor (for Mixed Choke Control).....................................................30
4.3.1.10 Offset Control............................................................................................................................ 30
4.3.2 PFC Output Setup................................................................................................................................ 31
4.3.2.1 Compensation Section Type, Nominal Power and Control State..................................................31
4.3.2.2 Discharge Time for Output Set 1/2...............................................................................................33
4.3.2.3 Output Set 2................................................................................................................................. 34
4.3.2.4 Switching Mode............................................................................................................................ 34
4.3.2.5 AOR – Automatic Output Recognizer...........................................................................................35
4.3.2.6 Manual Output Type & Power Filler..............................................................................................35
4.3.3 PFC Alarm Setup................................................................................................................................. 36
4.3.3.1 Standard Type Alarms.................................................................................................................. 38
4.3.3.2 Fast Actuation Reaction Alarms...................................................................................................39
4.3.3.3 NS> - “Number of Switching Operations Exceeded” Alarm..........................................................39
4.3.3.4 OE - “Output Error” Alarm............................................................................................................. 39
4.3.3.5 T1>< (T2><) - “Temperature Exceeded/Drop” Alarm..................................................................40
4.3.3.6 OoC - “Out of Control” Alarm........................................................................................................ 41
4.3.3.7 RCF - “Remote Control Failure” Alarm.........................................................................................41
4.3.4 Control / Manual State Indicator and Switch........................................................................................41
4.3.5 Power Factor Block Factory Setting.....................................................................................................41
4.4 PFC Block Operation................................................................................................................................ 43
4.4.1 Control State........................................................................................................................................ 43
4.4.2 Manual State........................................................................................................................................ 44
4.4.3 Automatic Output Recognition (AOR) Process...................................................................................44
4.4.4 CT Connection Test............................................................................................................................ 46
4.4.5 Single-Phase Mode............................................................................................................................. 49
4.4.5.1 Connection................................................................................................................................... 49
4.4.5.2 Setup............................................................................................................................................ 51
4.4.5.2.1 Connection Type 1Y3 / 1D3..................................................................................................51
4.4.5.2.2 Angle of Voltage Connected to the U1 Input (
U1-Angle )......................................................51
4.4.5.2.3 ACD Process – Automatic Connection Detection.................................................................52
4.4.5.3 Operation...................................................................................................................................... 54
4.4.6 Special PFC-Block Related Quantities's Meaning & Evaluation...........................................................54
4.4.6.1 Values Used for Power Factor Control Evaluation and Aggregation.............................................55
4.4.6.2 ΔQfh – PF Control Deviation....................................................................................................... 55
4.4.6.3 Cosφ / Tanφ / φ – Power Factor...................................................................................................55
4.4.6.4 CHL – Capacitor Harmonic Load Factor......................................................................................56
4.4.6.5 RC, RL – Compensation Reserve Powers...................................................................................57
5. METER BLOCK................................................................60
5.1 Basic Functions........................................................................................................................................ 60
5.2 Meter Block Manipulation and Setting....................................................................................................60
5.2.1 Data Area – Status Bar - Toolbar......................................................................................................... 60
5.2.2 Main Menu........................................................................................................................................... 61
5.2.2.1 Actual Data Group........................................................................................................................ 61
3