klover ECOMPACT 150, Installation, Use, Maintenance And Helpful Tips

Page: 48 / 56

42
PELLET-BURNING BOILER ECOMPACT 150-190-250-290 EN -
Rev 1.1
Parameter tables ECOMPACT 250
Parameters “VARIOUS CALIBRATIONS” - Mod. ECO250 (i05_220318)
Parameter Menu level Description Display Measurement Value field
Database
P0
Pr38 M08 – 4 – 01 Re-ignition block RE-IGNIT BLOCK Minutes 0 – 10 6
Pr39 M08 – 4 – 02 Flue gas extractor switch-off time MIN-EXT OFF Minutes 0 – 20 10
Pr40 M08 – 4 – 03 Pre-loading time in ignition IGNIT- PRE-LOAD Seconds 0 – 255 180
Pr41 M08 – 4 – 04 Stand-by time after pre-loading AFTER-PRE STAND-BY Seconds 0 – 255 160
Pr42 M08 – 4 – 05 Extractor speed in pre-loading phase
FLUE GAS-EXT
PRELOAD
RPM 350 – 2800 2100
Pr43 M08 – 4 – 06 ON/OFF temperature hysteresis on “SET H2O” DELTA ON OFF AUTO °C
0.0 – 20.0 5.0
Pr44 M08 – 4 – 07
Delay at economy operation mode switch-off (timer after reaching “SET
H2O” )
DELAY-OFF AUTO Minutes
2 – 120 20
Pr45 M08 – 4 – 08 Power change delay POWER CHANGE Seconds
0 – 60 20
Pr46 M08 – 4 – 09 ON/OFF Temperature hysteresis on “SET ROOM” DELTA ON AUTO °C
0.0 – 15.0 2.0
Pr47 M08 – 4 – 10 Keypad lock enable KEY LOCK-EN On – off On – off Off
Pr48 M08 – 4 – 11 Time after which an alarm is triggered in the event of a blackout BLACKOUT ALARM Seconds 0 – 60 30
Pr49 M08 – 4 – 12 Pellet level sensor enable PELLET RESERVE On – off On – off On
Pr50 M08 – 4 – 13 Pump start threshold and power modulation for overheating safety PUMP SAFETY °C 60 – 90 80
Pr51 M08 – 4 – 14
3-way switching and re-ignition delta on “SET BOILER” and “SET
BUFFER ”
DELTA PUF-BOI °C 0 – 15 5
Pr52 M08 – 4 – 15 Preheating time PREHEATING TIME Seconds 0 – 480 0
Pr53 M08 – 4 – 16 Extractor speed in preheating phase
PREHEAT-F.GAS-
SPEED
RPM 500 – 2800 2800
Pr54 M08 – 4 – 17
Time after which the “NO PELLET” alarm is triggered if “PELLET
RESERVE”
RESERVE ALARM Minutes 1 – 180 40
Pr55 M08 – 4 – 18 ON time for turbulator cleaning gear motor TURBOLAT DURATION Seconds 0 – 600” 120
Pr56 M08 – 4 – 19 ON time for brazier cleaning gear motor (NOT USED) CLEANING TIME Seconds 0 – 120” 0
Pr57 M08 – 4 – 20
Time from switching off after which the brazier cleaning takes place (NOT
USED)
CLEANER DELAY Minutes 1 – 15’ 1
Pr58 M08 – 4 – 21
Time from switching ON after which the brazier cleaning takes place (NOT
USED)
CLEANER STAND-BY Hours 1 – 24 24
Pr59 M08 – 4 – 22
Pump activation threshold and switching 3-way valve in DHW OUTPUT
MODE (with Type 2 System)
PUMP THRESHOLD I2 °C 55 – 75 60
Parameters “VACUUM CALIBRATIONS” - Mod. ECO250 (i05_220318)
Parameter Menu level Description Display Measurement Value field
Database
P0
Pr133 M08 – A – 01 Enable automatic pellet loading vacuum ENABLE VACUUM On – off On – Off Off
Pr134 M08 – A – 02 Vacuum on time VACUUM ACTIVE Seconds 1 – 180 20
Pr135 M08 – A – 03 Vacuum rest time VACUUM PAUSE Seconds 5 – 60 10
Pr136 M08 – A – 04 Number of operating cycles VACUUM CYCLES Number 1 – 20 15
Pr137 M08 – A – 05 Enables a Vacuum operating test to be performed VACUUM TEST On – off On – off Off
Parameters “FACTORY CALIBRATIONS” - Mod. ECO250 (i05_220318)
Parameter Menu level Description Display Measurement Value field
Database
P0
Pr01 M08 – 6 – 01 Ignition cycle maximum time IGNIT- MINUTES Minutes 5 – 25 18
Pr02 M08 – 6 – 02 Start time START MINUTES Minutes 2 – 12 8
Pr03 M08 – 6 – 03 Time interval between the two brazier cleaning operations BRAZIER CLEANING Minutes 3 – 240 90
Pr04 M08 – 6 – 04 Screw feed gear motor ON time in ignition phase IGNIT- SCREW FEED Seconds 0.1 – 8.0 0.9
Pr05 M08 – 6 – 05 Screw feed gear motor ON time in start phase SCREW FEED START Seconds 0.1 – 8.0 1.2
Pr06 M08 – 6 – 06 Screw feed gear motor ON time in power 1 work phase
OUTPUT 1 SCREW
FEED
Seconds 0.1 – 8.0 2.8
Pr07 M08 – 6 – 07 Screw feed gear motor ON time in power 2 work phase
OUTPUT 2 SCREW
FEED
Seconds 0.1 – 8.0 4.0
Pr08 M08 – 6 – 08 Screw feed gear motor ON time in power 3 work phase
OUTPUT 3 SCREW
FEED
Seconds 0.1 – 8.0 5.0