Kingfisher KI 2300 Series Operation And Maintenance Manual Download Page 59

Page: 59 / 74

PERFORMANCE VERIFICATION TESTS

KI2000 UM-6

57 -

Short Term Stability Test (optional)

Connect the Light Source to the Power Meter as shown. For

better stability, ensure that connector plugged into power
meter has APC termination.

Set the optical power meter to 1310 nm. 3.

Light

Source, enable the source and set the wavelength to 1310 nm.

Let the unit warm-up for 15 minutes then note the power.

Record the power every 30 seconds for 3 minutes.

Calculate max-min values for stability (< 0.1dB).

Record test results in Table 5.

Light Source Power Meter

Note: The same instructions apply to Short Term Stability Test on
850/1300 nm Light Sources. For improved stability, mandrel wraps
should be used in the case of 850/1300nm.

Time

Measured power,
dBm

Drift, dB

Tick max/min
values

00 sec

0.00

30 sec

60 sec

90 sec

120 sec

150 sec

180 sec

Summary of Contents for KI 2300 Series











































































Search results

Summary of Contents for KI 2300 Series

Reviews:

Related manuals for KI 2300 Series

Brands by name

Popular brands

Kingfisher KI 2300 Series, Operation And Maintenance Manual

Search results

Summary of Contents for KI 2300 Series

Reviews:

Related manuals for KI 2300 Series

Brands by name

Popular brands