Kingfisher KI 2300 Series Operation And Maintenance Manual Download Page 11 | Manualshive

Page: 11 / 74

background image

INTRODUCTION AND APPLICATIONS

KI2000 UM-6

-

9 -

Laser sources at 1310 / 1490 / 1550 / 1625 nm are used for testing
single mode fiber systems, and LED sources at 850 / 1300 nm are
used for testing multimode fiber systems. The innovative VisiTest

option is helpful for general loss testing, continuity testing and fault
finding.

LED sources are mode controlled and compliant with Encircled Flux &
CPR test standards. The 1300 nm LED can also perform short
distance single mode testing.

Laser / LED light sources have re-connection repeatability of 0.1dB /
0.05 dB. Combined with the instrument excellent stability, this provides
more accurate measurement results.

Multi-fiber ID allows for easy multi-fiber identification of up to 12 fibers
at a time. To use this feature, multiple light sources are set up on
multiple fibers, with each one set to a different tone. When a tone is

detected by a power meter, a buzzer sounds and the corresponding
fiber ID number is displayed.

KI2400 series include zero warm up ultra stable laser and LED light
sources with laser stability of ± 0.03 dB.

«
...
9
10
11
12
13
...
»

Summary of Contents for KI 2300 Series











































































Reviews:

No comments

Related manuals for KI 2300 Series

Brand: Eaton Pages: 43

Brand: Daewoo Pages: 2

Brand: Yamaha Pages: 98

Brand: THORLABS Pages: 21

Brand: Oldham Pages: 96

Brand: Chroma Pages: 63

Ranger TDR VDV501-090

Brand: Klein Tools Pages: 44

Brand: PRONIVO Pages: 40

Brand: socomec Pages: 34

Brand: Fluke Pages: 6

Brand: Konica Minolta Pages: 48

Photo Set Strato S-20

Brand: Fisso Pages: 2

Brand: Televes Pages: 2

MJK MagFlux Series

Brand: Xylem Pages: 179

Brand: jacarta Pages: 44

Brand: Bushnell Pages: 64

Brand: Omega Engineering Pages: 42

Brand: RMG Pages: 156

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands