Kingfisher KI 2300 Series Operation And Maintenance Manual Download Page 58 | Manualshive

Page: 58 / 74

background image

PERFORMANCE VERIFICATION TESTS

KI2000 UM-6

-

56 -

Optical Light Source

Output Power (CW) Test

1.

Connect the Light Source to the Power Meter as shown.

2.

Switch on the instruments.

3.

Set the Optical Power Meter to 1310 nm

4.

On Light Source, enable the source and set the wavelength to

1310 nm.

5.

Note the measured power level value in the test report in
Table 5.

6.

Repeat the above on 1550 nm.

Light source

Power Meter

«
...
56
57
58
59
60
...
»

Summary of Contents for KI 2300 Series











































































Reviews:

No comments

Related manuals for KI 2300 Series

PowerCross-Laser 8 S

Brand: LaserLiner Pages: 64

ClimaHome-Check Plus

Brand: LaserLiner Pages: 10

MeterMaster Plus

Brand: LaserLiner Pages: 104

Brand: LaserLiner Pages: 52

LaserRange-Master T2

Brand: LaserLiner Pages: 52

Brand: LaserLiner Pages: 5

CombiRangeXtender 40

Brand: LaserLiner Pages: 84

SuperCross-Laser 2P

Brand: LaserLine Pages: 92

MoistureFinder Compact

Brand: LaserLine Pages: 56

LaserRange-Master Gi7 Pro

Brand: LaserLiner Pages: 56

Brand: Laser Tools Pages: 4

SmartVision-Laser

Brand: LaserLiner Pages: 56

Brand: Zeversolar Pages: 35

Brand: Zenner Pages: 52

Brand: Gearx Pages: 19

Brand: ADA INSTRUMENTS Pages: 27

Brand: Vigor Equipment Pages: 12

Brand: Kane Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands