Kikusui OT01-PCR12000LA/2 Operation Manual Download

Page: 5 / 96

OT01-PCR-LA/2

Safety Precautions III

Installation

• When installing products be sure to observe “Installation” described in this man-

ual.

• To avoid electrical shock, connect the protective ground terminal to electrical

ground (safety ground).

• When connecting the power cable to a switchboard, be sure work is performed by

a quali

ed and licensed electrician or is conducted under the direction of such a

person.

• When installing products with casters, be sure to lock the casters.

Relocation

• Turn off the power switch and then disconnect all cables when relocating the

product.

• Use two or more persons when relocating the product which weights more than

20 kg. The weight of the products can be found on the rear panel of the product
and/or in this operation manual.

• Use extra precautions such as using more people when relocating into or out of

present locations including inclines or steps. Also handle carefully when relocat-
ing tall products as they can fall over easily.

• Be sure the operation manual be included when the product is relocated.

Operation

• Check that the AC input voltage setting and the fuse rating are satis

ed and that

there is no abnormality on the surface of the power cable. Be sure to unplug the
power cable or stop applying power before checking.

• If any abnormality or failure is detected in the products, stop using it immediately.

Unplug the power cable or disconnect the power cable from the switchboard. Be
careful not to allow the product to be used before it is completely repaired.

• For output wiring or load cables, use connection cables with larger current capac-

ity.

• Do not disassemble or modify the product. If it must be modi

ed, contact Kikusui

distributor/agent.

Maintenance and checking

• To avoid electrical shock, be absolutely sure to unplug the power cable or stop

applying power before performing maintenance or checking.

• Do not remove the cover when performing maintenance or checking.

• To maintain performance and safe operation of the product, it is recommended

that periodic maintenance, checking, cleaning, and calibration be performed.

Service

• Internal service is to be done by Kikusui service engineers. If the product must be

adjusted or repaired, contact Kikusui distributor/agent.

Check?

Summary of Contents for OT01-PCR12000LA/2

































































































Search results

Summary of Contents for OT01-PCR12000LA/2

Reviews:

Related manuals for OT01-PCR12000LA/2

Brands by name

Popular brands

Kikusui OT01-PCR12000LA/2, Operation Manual

Search results

Summary of Contents for OT01-PCR12000LA/2

Reviews:

Related manuals for OT01-PCR12000LA/2

Brands by name

Popular brands